Question about Hobart Handler 140 Mig Welder

1 Answer

Hobart135 when on and pres triger wire wont run

When my welder is on and press the triger the wire would not run the wire wheel wont spin

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 597 Answers

Is there a feed speed adjustment?

Posted on Jun 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Problem is when i triger the handle i only heard a clik but wire motor wont work


Either the drive motor for the rollers or the wire speed control needs fixing or replacement. The click you are hearing is the solenoid connected to trigger trying to run the drive motor.

Sep 05, 2015 | Welding Tools

1 Answer

Why wont the wire come through my cosmo gas gasless welder


Most mig welders have reversible feed spools. There is a good chance you have the spool in the .030 wire side. Remove the spool retaining clip and flip the spool to .023 wire for example. I don't know what size wire you are using. Also there is an adjustment for the drive spool. Tighten the tensioner spring thumb screw to increase the feed tension.

Apr 28, 2014 | Welding Tools

1 Answer

Lincon mig stops feeding wire


Been welding for a while, open side, check for proper tension on the feed wheel inside side panel, hit the trigger, if feed motor continues to spin tensioner needs tightened or mig wire may be getting hung up inside main cable lead. If motor is off on off on then its probbably the switch on the trigger getting a bad good connection, hope this helps o and check welding tip on gun end, may need replaced if worn or melted, unscrews.

Mar 05, 2012 | Welding Tools

1 Answer

The welder fan is running and when i push triger air flows but wire motor does not run


Check the heat resistor which is located on the circuit board behind the wire speed dial! Looks like a white oblong component and tends to desolder itself through heat on the board! Resolder it back in and it should work again!

Nov 27, 2010 | Clarke Power Products Mig/Fluxcore 180En...

1 Answer

175handler quit spooling the wire . it still clicks when you pull the triger but moter does not turn


Do the drive wheels turn? Take wire out of drive rolls to see if they will turn! If they turn you could have possibly pinched the liner in your mig gun that your wire passes through. If so you will have to change it out. Good luck!

May 22, 2010 | Welding Tools

1 Answer

I have a Marquette m12209 mig that wont feed. fan runs and lights are on and fuses are good. anyone have a wiring schematic?


check the wire drive motor it may have burnt out also check the wire wheel drive teeth they may be slipping and dont try using rusty wire it rips the teeth off the wire drive wheel if this is all good check the neck triger switch if thats not working the wire feed wont work then take out the nippel and pull the wire through it to check its free in the feed tude with no kinks in it,,,

Mar 10, 2010 | Welding Tools

1 Answer

WIRE WONT FEED WHEN TRIGER IS PRESSED NOR IS THERE ANY ARK. THE WAND AND CABLE HAVE BEEN CHECKED AND ARE OK


if it is new make sure the trigger is connected inside area where the wire is.

Feb 26, 2010 | Welding Tools

1 Answer

Solar welder 2175 wire keeps feeding wont stop doesnot arc until trigger is pulled


Look on the front pannel. thier should be a "latching Switch" indicated by "4 X 2" little arrowes. The 4 is " pull the triger -- the release the arc continues, the "2" is pull the trigger and the arc startes release the trigger the arc stops simplesssssssss
Ken

Dec 14, 2009 | Welding Tools

Not finding what you are looking for?
Hobart Handler 140 Mig Welder Logo

Related Topics:

263 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hobart Welding Tools Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Matt Olenzek
Matt Olenzek

Level 2 Expert

293 Answers

Troy
Troy

Level 1 Expert

35 Answers

Are you a Hobart Welding Tool Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...