Question about Virtual Reality Sound VR3 CD Player w/ USB and Scan Disk Inputs

1 Answer

I have a Dual XDM7510 and i can't figer out how to get the face plate off of it

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 655 Answers

Hello sneary_08,

The front panel was semi-permanently attached during
assembly. In order to be removable, the installer is required to follow specific procedures contained in separate instructions. If the installer did not perform the procedures, the front panel will not be removable.

If the procedure was followed during initial installation, then you can remove the front panel as follows:

With the unit off, press OPEN to allow the front panel to slide
down. Gently squeeze the release tab located on the bottom
center underside and pull front panel down and away from
unit to remove. To install, insert left side first, then push
right side to secure.

Hope this helps.

Posted on Jun 01, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Schematics for dual xdm7510


You would need to contact Dual for these.

Dec 05, 2016 | Dual Car Audio & Video

1 Answer

Dual CD770 (Same as XDMR7700) face stuck open (down)


Change the Flex cable that connects from main chassis to the front face plate. This is a common problem with Dual drop down face plates, since the flexible wires break and lose connection.

Mar 06, 2013 | Dual XDMR-7700 CD Player

1 Answer

On the back of the dual xdm their is a nut in the middle is that an accesory ground


It could be used as a ground but the main purpose is to hold the cooler (the black aluminum piece on the back of the radio) in place so the radio head unit doesnt overheat.

Mar 09, 2012 | Dual Electronics XDM7510 CD Player

1 Answer

How does the Iplug work on the xdm7510 car radio....i have on and i want to use my mp3 player how do i do that????


you have to switch modes until you are on aux (just like hitting TV/VCR on your remote at home)

Feb 27, 2011 | Dual Electronics XDM7510 CD Player

1 Answer

Dual Electronics XDM7510 CD 770 Player.It comes on but no sound,speakres pop when cut on.


Go check out this manual: http://www.fixya.com/support/p920254-dual_electronics_xdm7510_cd_player/manual-26883

Jan 11, 2010 | Dual Car Audio & Video

1 Answer

Where can i plug in my ipod?


XDM7510 CD Player This dual model radio it comes w/ a Aux, wire plug where it need to be connect it from back of stereo first.

Jan 04, 2010 | Dual Electronics XDM7510 CD Player

1 Answer

Xdm7510 will not accept any disc


try unhooking the battery for a couple minutes then hooking it back up

Sep 25, 2009 | Dual Electronics XDM7510 CD Player

1 Answer

How do I turn my subs on on my xdm7510 radio


check to see if you have power going to the amp. Battery(+) and Negatve(ground). if those are ok, turn the radio on and check to see if the remote wire(it's usually blue) has power. if you have power on the battery wire and the remote wire from the radio, then there is a problem with your amp. check fuses on the amp if any.

Sep 07, 2009 | Dual Electronics XDM7510 CD Player

2 Answers

My Dual XDM7510 display quit working and I can't find out what is wrong. Everything else on the XDM7510 works. Help me please. It was working when I went in the store came back out and no display.


try checking the illumination light on the back of the radio if that doesnt work then try looking at the red ignitionswitch wire and make sure it is connected to the 12vt constant (the yellow wire)

Mar 10, 2009 | Dual Car Audio & Video

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

360 people viewed this question

Ask a Question

Usually answered in minutes!

Top Virtual Reality Car Audio & Video Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Mark Skinner

Level 2 Expert

77 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Virtual Reality Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...