Question about Whirlpool 30" Self-Cleaning Freestanding Electric Range - White-on-White

1 Answer

What does an F1 fault indicate

What does a Maytag over F1 fault mean? Thank you

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 85 Answers

MAYTAG
Range/Stove/Oven Fault Codes Failure
Code
Condition Check/Repair F1 Defective touch pad or membrane Replace touch pad or membrane (usually the touch pad)* F1 Watchdog on board Replace touch pad or clock assembly (also called the ERC) F2 Oven too hot Replace relay board (if present) or bad oven temperature sensor F3 or F4 Open or shorted oven temperature sensor Replace oven temperature sensor F5 Hardware and watchdog circuits disagree Replace clock assembly (also called the ERC) F6 Missing AC signal Check for proper voltage F7 Function key shorted or stuck button Replace touch pad or clock assembly (also called the ERC) or un-stick button F8 Analog/Digital supervisory Replace clock assembly (also called the ERC) F9 Door latch supervisory Check door lock circuit or replace clock assembly (also called the ERC) F0 Function key stuck Replace touch pad or clock assembly (also called the ERC) * Here is a simple test that you can do to determine whether the clock or the touchpad are defective when the display reads F1:

- Disconnect power to the range.
- Gain access to the back of the ERC (electronic range control, or "clock").
- Unplug the touch pad ribbon connector from the ERC. This will be a flat wire about 1 ½" to 2" wide.
- Make sure everything is clear and will not short out when power is turned back on. Replace any covers removed to gain access to the ERC.
- Turn the power back on to the range.
- Watch for the F-1 and listen for the beep.
- If you get the F-1 and beep, replace the ERC.
- If after approximately 60 Minutes you do not get the F-1 fault, replace the touch pad.

NOTE: Some models incorporate the touch pad and the clock control as one part so F1 = bad clock control.

Warning: If you do not feel comfortable doing this test or making this repair please contact a qualified appliance repair technician.

Posted on Jun 01, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

GE model # jkp27 error code F1 what should I do?


Hi ssantillo,

Usually F1 error code means that either the touch pad or the oven control (also called clock or ERC) is defective and needs to be replaced. If this fault code cannot be cancelled, replace the oven control (also called clock or ERC), touch pad, or both.

Hope this helps.

Thank you for using FixYa.

Apr 27, 2011 | GE JKP27 Electric Double Oven

1 Answer

My oven is beeping and the F1 code and F7 code are appearing on the screen


Hi

F1 indicates a fault on the electronic oven controller (the clock) & F7 means a function key is stuck.

Check all the keys on the keypad if the fault remains you probably need a new clock.

Dec 19, 2010 | Thermador SC302T Electric Double Oven

1 Answer

I have a maytag range/oven model mgs5770adb and keep getting an F1 code on the display


The F1 code indicates that:

a. The electronic range control (ERC) is sensing heat in the oven when in a time-of-day (1.e., not cooking) mode or

b. The ERC is receiving information to run multiple heat functions simultaneously.

Although different components (depending upon the model) could generate the code, simple and straightforward testing using your ohm meter is all you gotta do to test for it.

1. Check the oven temperature sensor. The oven sensor gotsta be within spec or it will cause the F1 code. As an example of being out-of-spec, the ERC will generate an F1 fault code when the sensor shows 1650 ohms during a time-of-day mode. This is equivalent to 350°F in the oven. The resistance isn't high enough to generate an F2 code (runaway temp) or an F3 or F4 code (shorted/open sensor circuit). The ERC monitors the sensor circuit after a heat cycle and expects the resistance to drop back to 1050-1100 ohms. The fault code is generated when this doesn't happen. Checking the sensor circuit means also checking the harness, harness connections and the sensor itself.

2. If the oven sensor circuit checks okay, then turn your inquisitive eyeballs to the touchpad. If the range has a separate touchpad/keyboard, the keypad may have moisture that is shorting several circuits simultaneously. If the F1 code is given immediately (instead of during or after a heat cycle), remove the ribbon connector from the touchpad to the ERC after clearing the F1 code. If the F1 code does not return in five minutes, then cast a suspicious gaze upon the touchpad/keyboard. Shorts may be caused by using an ammonia-based glass cleaner. The touchpad surface will absorb ammonia-based cleaners that are sprayed directly on the glass surface. When heat is applied, the surface material can break down causing shorts. If you're gonna use ammonia-based cleaners on your control panel, then you should spray it on the rag and then wipe the touchpanel -don't spray directly onto the surface of the touchpad.

3. If these tests all check good, then replace the ERC.

Sep 23, 2010 | Maytag Ovens

1 Answer

F1...


hello,

what this code mean is an error code indicating that there is a lost of connection on the door or on the control panel meaning that the door is not properly close

thank you and thanks for using fixya.

Jul 09, 2010 | Maytag Ovens

1 Answer

Can you tell me what an F1 error Message means - 30 minutes into baking, I got beeping and an F1 error message. Canceling did not turn the oven off and the only thing I could do is turn it off at the...


Hi,

"F1" code clearly indicates that main control board has failed. The possible fix for this kind of problem is you have to replace the faulty circuit board. This is the only solution and you cant repair anything else in this unit when F1 flashes.
Thank you !!

May 30, 2010 | Kenmore 40494 / 40495 / 40499 Electric...

1 Answer

What does F1 mean?


Fault Code 1. This model has a "Table" of "Fault" codes, the machine is indicating it is faulty.

Feb 13, 2010 | Ovens

1 Answer

I get an F1 symbol on mt electric oven


The F1 error code usually means the oven temperature has exceeded the safe limit for the oven.

Usually this is an indication that the temperature sensor has failed 'on' allowing the heating element to overheat the oven.

You would need to have the temperature sensor replaced.

Jan 13, 2010 | Maytag 30 in. Electric Single Wall Oven...

1 Answer

Maytag electric stove w/ovenMODEL #-MER5750BAW I'm geetting an F1 error code after the oven heats up. Can I find out what this coad means?


F1 code is a defective electronic control(clock). There is no reset or quick fix. The EOC must be replaced.

Dec 25, 2009 | Maytag Ovens

1 Answer

F1 is displayed on Maytag Electric Oven I ran the self-clean cycle on my Maytag Model MER5530 oven yesterday; before it completed F3 was displayed and beeps sounded. I pressed CANCEL, the F3...


Hi

F1 error means that you have either a bad ERC (clock) or a bad touch pad. To check these please follow these simple instructions:
  1. Disconnect power to stove
  2. Gain access to the back of the clock (electronic range control or ERC).
  3. Unplug the touch pad ribbon connector from the ERC. This will be a flat wire approx. 1 1/2" to 2" wide.
  4. Make sure everything is clear and will not short out when power is turned back on.
  5. Turn power back on to stove.
  6. Watch for the F1 and listen for the beep.
  7. If you get the F1 and beep, replace the ERC.
  8. If after approx. 30 minutes you do NOT get the F1 and hear the beep, replace the touch pad...
thank u
rate me!!!

Aug 14, 2009 | Maytag Ovens

1 Answer

F1 fault code on Jenn-Air jwg 8130


hi,
The F1 ErrorOn a number of ranges this can mean a number of things, the most common being a failed ERC(EOC, Clock assembly)or a faulty touchpad. Firstly if you are using a recent Maytag range it may pay to test the oven sensor as described above as this may cause an F1 error if faulty (may apply to some other ranges as well) this is not a common cause but is worth discounting. To check the ERC and touchpad 
Disconnect the power
Gain access to the back of the ERC
Disconnect the ribbon cable that connects the ERC to the touchpad
Check nothing will short when power is reconnected
reconnect the power and switch on
Watch for F1 and listen for the beep
If you get the F1 and the beep this means the fault is with the ERC and it will need replacing 
If after 30 mins you do not see the F1 error and hear the beep, replace the touchpad

or follow the link for more info:
http://www.appliancefactoryparts.com/applianceshvac/help-center/fault-codes/fault-codes-ranges.html#Admiral

thanks for your question.

Jan 03, 2009 | Jenn-Air JGW8130DD Gas Single Oven

Not finding what you are looking for?
Whirlpool 30" Self-Cleaning Freestanding Electric Range - White-on-White Logo

425 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Ovens Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

 Fix Your Board
Fix Your Board

Level 3 Expert

310 Answers

ashburton

Level 3 Expert

417 Answers

Are you a Whirlpool Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...