Question about Jacuzzi MAGNUM FORCE POOL PUMP - TWO SPEED 2 HP 115/230V

1 Answer

I have a Jacuzzi Magnum force pump

Wright behind the strainer basket there is a leak in the housing. I have a 12 year warrenty. We had the pool installed in 2001. Where can I go to get the replacement part . This part would be the from the front inlet connection to where the motor is connected with the ring lock. Thank you for your time. Patti- Jo Parks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Jacuzzi Master
  • 1,378 Answers

Good luck...Jacuzzi went out of business. The best source I have had for their parts is CCO:

http://www.jbparts.com/jbc0001.html

Posted on Jun 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Jacuzzi pool pump leaking


Where is it leaking? if it is still leaking between the wet end which is the black plastic water housing and the motor then the seal is not properly set.

Rod
US Parts Center

Aug 04, 2012 | Jacuzzi Magnum Force Series Pool Pump 1...

1 Answer

My jacuzzi magnum force pump is hot is this normal?


the pump is pumping and circulating hot water into jacuzzi, it will get hot. I think it is ok

Jul 06, 2012 | Jacuzzi Magnum Force Series Pool Pump 1...

1 Answer

Pool pump running low psi


your pump should be just fine once the water starts flowing again. You may have run it too long without enough water to cool the seal.
If it is leaking water between the Jacuzzi Pump housing and the motor then you will need a new pump seal. Those are common pool parts.

Rod
US Parts Center
888-521-6183

Jun 09, 2012 | Jacuzzi Magnum Force Series Pool Pump 1...

1 Answer

How to change the seals on a jacuzzi magnun force 1 hp pool pump


Hi,
If you haven't already figured out how to change the seals on your Jacuzzi Magnum Force pump, I can help by supplying a diagram.
Here is the parts explosion for that pump.
Start by removing the case/basket assembly, then the diffuser to get to the impeller. Loosen the impeller to get to the seal plate.
When going to the trouble of changing the shaft seals one should change all the hosing seals at the same time because its a lot of work.

Jul 02, 2011 | Jacuzzi MAGNUM FORCE POOL PUMP 2 HP...

1 Answer

Pump housing is cracked and lealing. Is there any


the pump housing is available through your local pool dealer. It is broken down into 3 sections the pump, housing and Pod.

The Pool Tech

Jul 01, 2010 | Jacuzzi MAGNUM FORCE POOL PUMP 2 HP...

2 Answers

I have a magnum pump. when i turn it on. the pump hums and then clicks off like it has shorted out. but i still here it on. it will not pull water from pool


Pumps will **** all sorts of debris and many times the debris is small enough to get thru the strainer baskets and block the pump inlet. Turn the power off at the breaker, remove the strainer basket, and reach in with your fingers and check for debris in the pump inlet.
Clear all you can get out by hand, then on the outside of the pump motor, take the cap off the shaft, and turn it back and forth with a crescent wrench. Then put the basket and lid back on and turn the pump on.... you may need to clear it this way a few times to get it back up to speed, but that sounds exactly like what I've been dealing with at my wonderful pool that's right next to a 50 evergreen dropping needles 24-7 this time of year.... hope you clear it up ....let me know how it goes.
k

Aug 03, 2009 | Jacuzzi MAGNUM FORCE POOL PUMP - TWO SPEED...

1 Answer

Jacuzzi Magnum Force Pump not working


The number one problem is air leaks.......check all connections to see that they are tight, and rubber seals. The intake side would give you trouble with air leaks. If you dont find any leaks then I would pull the pump cover and check the impellor. Pool stores have parts and lots of knowledge.

Jun 09, 2009 | Jacuzzi MAGNUM FORCE POOL PUMP - TWO SPEED...

1 Answer

My pump is running however it's pressure is less than 10 psi and the heater on the pool will not run.


With the Jacuzzi Magnum pool pumps, low pressure is going to likely be cause by one of the issues below. Try these troubleshooting tips.

1.Pump not primed

2.Leakage of air into suction system

3.Impeller clogged

4.Valve in suction or discharge line partly closed or suction or discharge line partly plugged or too small. 5.Plugged basket in skimmer or hair in lint strainer.

6.Dirty filter.

Jun 06, 2009 | Jacuzzi MAGNUM POOL PUMP 1-1/2 HP MAGNUM...

Not finding what you are looking for?
Jacuzzi MAGNUM FORCE POOL PUMP - TWO SPEED 2 HP 115/230V Logo

Related Topics:

306 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jacuzzi Pool & Spa Experts

Jay Finke
Jay Finke

Level 3 Expert

1338 Answers

Mike

Level 3 Expert

4336 Answers

john h

Level 3 Expert

11057 Answers

Are you a Jacuzzi Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...