Question about Craftsman 25cc Gas Line Trimmer

Open Question

Pull cord Need to replace pull cord. Any easy steps. Craftsman Bruchwacker model 358-795200

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

erickg
  • 116 Answers

SOURCE: REplacing the pulling cord on a gas trimmer

those are usaully under your pull start cover and if its broke you can buy a new rope but if its broke near handle i would open it and retie it to save ya money. but remember to wind spring a little to keep tension on it before pushing it through the hole for handle.

Posted on Apr 17, 2009

  • 27 Answers

SOURCE: broken pull cord

ur going to have to unmount the the motor from the shaft

step 1. Unbolt throttle housing

step 2. now with that out of the way u should see a clamp holding the motor to the shaft, loosen and pull the shaft out, there will be a cable, so make sure u have it lined up so it goes back into place

step 3, look at the back of the motor, u should see screws going into the plastic housing (coming in from back going into plastic)

step 4. once that is off pull the broken part of the cord out

step 5. wind up the starter coil, (it will only wind up one way) its spring loaded so be carful, once it stops back it off 1 full turn

step 6. u will see a hole for the cord in the housing and in the coil, make sure they are lined up

step 7. insert the cord through both holes, tie it as tighttttt as possible, then let the spring do the rest

step 8. put it back together

Posted on May 31, 2009

  • 5 Answers

SOURCE: pull cord broke on my craftsman gas push edger. I

It sounds like you did not properly rewind the spring that is behind the spool that the cord would around, that spring is what rewinds the cord after pulling the cord.

Posted on May 06, 2010

  • 12104 Answers

SOURCE: I have a Craftsman walk-behind Gas edger. Model

before u buy a new housing check ur spring did u rewind the pull cork enough or check if the spring disconnected from its clip

Posted on May 06, 2010

  • 220 Answers

SOURCE: I NEED TO REPLACE THE

Try Sears...They sell/have appl. parts. You'll be amazed at what they have.

Posted on Apr 21, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace pull cord on craftsman weed wacker model 316.791080?


is the pull cord in the front of the motor if it is it is not worth fixing it will take about two hrs to fix the motor will have to be pulled..

Jul 18, 2011 | Garden

1 Answer

Pull cord broke on my craftsman gas push edger. I replaced cord but when I pull cord..It wont rewind but I can hear it trying to start


It sounds like you did not properly rewind the spring that is behind the spool that the cord would around, that spring is what rewinds the cord after pulling the cord.

May 05, 2010 | Craftsman Garden

1 Answer

Replacing a pull cord on a Craftsman mower


u helped tremondous. thank you, being laid-off i need my mower

Mar 29, 2010 | Craftsman Garden

1 Answer

How do i untangle the pull cord on my leaf blower, it is jammed inside (210MPH/450CFM Craftsman)


just tack the recoil off they are usually easy to remove do to the nature of the part then you should be able to unwind and untangle. in the future dont let go of the cord until it is wound back up that will elininate the back lash and tangling

Oct 31, 2009 | Craftsman 4 Cycle Blower/Vac

1 Answer

Broken pull cord


ur going to have to unmount the the motor from the shaft

step 1. Unbolt throttle housing

step 2. now with that out of the way u should see a clamp holding the motor to the shaft, loosen and pull the shaft out, there will be a cable, so make sure u have it lined up so it goes back into place

step 3, look at the back of the motor, u should see screws going into the plastic housing (coming in from back going into plastic)

step 4. once that is off pull the broken part of the cord out

step 5. wind up the starter coil, (it will only wind up one way) its spring loaded so be carful, once it stops back it off 1 full turn

step 6. u will see a hole for the cord in the housing and in the coil, make sure they are lined up

step 7. insert the cord through both holes, tie it as tighttttt as possible, then let the spring do the rest

step 8. put it back together

May 30, 2009 | Craftsman 25cc Gas Line Trimmer

Not finding what you are looking for?
Craftsman 25cc Gas Line Trimmer Logo

Related Topics:

267 people viewed this question

Ask a Question

Usually answered in minutes!

Top Craftsman Garden Experts

Dean Gruber

Level 2 Expert

110 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

486 Answers

Dennis Key
Dennis Key

Level 3 Expert

2478 Answers

Are you a Craftsman Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...