Question about Beko 24 in. D3421F Free-standing Dishwasher

1 Answer


Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 417 Answers
Re: BEKO D3422FS

Check that there are no kinks in the drain pipe or that the pipe way is clear.

Thanks J

Posted on Feb 16, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

2 Answers

I have a beko 4311w dish washer that wont empty. i emptyed the water manually and have checked all filters and hoses and all seemed to be clean.then switched back on and machine completed one complete...

The motor runs in one direction to wash and the opposite direction to pump out the water. Look at the motor direction controls to see what is starting to fail.

Jan 03, 2015 | Beko Dishwashers

1 Answer

Brand new beko DE 2542 PW dishwasher won't start wash cycle

It sounds as if the d/washer is pressurising due to a blocked outlet drain hose.

Make sure that the drain for the dishwasher is actually clear take hose out of the drain outlet.On some of the Beko dishwashers they put a plug up inside the drain hose which has to be removed before use or if it is a new installation and it is draining into a "U" bend on a sink check that the little spigot that the hose is onto is actually open.They come from the plumbers merchants blanked if blanked then you have to cut the end off to suit size of hose.I hope this has helped.

Good Luck.

May 09, 2010 | Dishwashers

1 Answer

I have disconneted a pump to the Beko D3422FS to check and clean the impeller. Sadly I didn't take clear enough notes on the wiring connections and the macine is now tripping the mains. Does anyone have a...

i downloaded some circuit diagrams from rapidshare after contacting an expert on

Alternative locations:

There are three wires on the base of the motor, Red, Brown and White.

The White conects to the double violets on a conector
The Red to one side of the capacitor (side nearest the motor)
The brown one caused a lot of confusion. I believe this attached both to the yellow connection and then onto the spade connection on the other side of the capacitor.

This is one I slept on, and had an Epiphany.

The circuit diagrams didn't apear too clear to me. They don't sem to indicate which connections go to the capacitor, just the pump cluster as a group. I may be wrong, but have connected as above and will get the father-in-law to check them before I plug the machine back in.

Jan 31, 2010 | AEG Dishwashers

1 Answer

I have a Beko D 2731 FW its about 4 years old and recently it has begun to leave a gritty deposits. I think this may be due to the top spray arm not running as freely as it used to. I would appreciate any...

Here are a few things to check.

* Worn wash impeller (depending on design). Test by placing a glass upright in upper rack with full charge of water in the basin. Run dishwasher for 30 seconds. Glass should fill up. If not, replace wash impeller.

* Debris caught in spray arm holes. Remove spray arm and clean out with water and compressed air.

* Heating element burned out. Check water temp during wash--should read between 130 to 140 F.

* Insufficient water fill in basin. In most models, proper fill level is just up to the heating element. Much less than this will result in poor cleaning.
Hope this helps.

Sep 08, 2009 | Beko Dishwashers

1 Answer

Beko dwd4310 not running

Hi Kirsty did you solve this? I have the same problem.

Jul 22, 2009 | Dishwashers

1 Answer

Beko washing machine fills with water when not in use!!

hi got a faulty water inlet valve on the machine ..change this and all will be fine again...

regards Sir Galahad

Dec 05, 2008 | Beko 24 in. D3421F Free-standing...

1 Answer

Beko washing machine

hi there.......this problem could be caused by a failed heater element ...if the element is not heating the machine will just wash wash etc...the front panel will have to be removed to check the heater element....if the element is ok...check the heater NTC ( little white plug in the heater element)...if all ok here....then you have a main PCB board failure....

it may be more economic to have beko send an engineer to you...

regards Sir Galahad

Nov 03, 2008 | Beko 24 in. D3421F Free-standing...

2 Answers

Beko 2431 dishwasher not working

I have the same problem
dishwasher seems to try to wash but not get anywhere.
have tried tipping dishwasher to empty excess water out, filters and arms cleaned.
dishwasher just takes in water, hums for a bit and then the cycle ends after about 20 mins but obviously dishes are not clean

Jun 05, 2008 | Beko 24 in. D3421F Free-standing...

1 Answer

Beko eco washing machine

Sounds like a pump problem. Could be a broken impeller, or something has got past the filter and has jammed it. Try removing the filter assembly inside, and see if anything is visible in the pump chamber. It may be too late and the pump is broken.

Oct 17, 2007 | Beko 24 in. D3421F Free-standing...

Not finding what you are looking for?
Beko 24 in. D3421F Free-standing Dishwasher Logo

Related Topics:

377 people viewed this question

Ask a Question

Usually answered in minutes!

Top Beko Dishwashers Experts

Shekar Avadhani

Level 2 Expert

60 Answers


Level 3 Expert

57192 Answers

David Payne
David Payne

Level 3 Expert

13437 Answers

Are you a Beko Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides