Question about Coleman Powermate Powermate 5000W Generator

1 Answer

Pull start recoil assembly

Where can I find a replacement recoil assembly for my coleman powermate pulse 1850?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I bought a replacement recoil starter for my 1850 at Pats small engine parts. The part number for a 3.5 B & S is 499706. If you look on the heat shield on the side of the motor there is the engine model and s/n. Hope this helps.

Posted on Jun 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change recoil on coleman powermate 1850 pull start wont go back in


I think the rope has jammed in the side of the starter's internal pulley. Remove the starter housing - you should see the rope bound up on the edge of the pulley. Free it up and put the housing back on.

Aug 01, 2014 | Coleman Electrical Supplies

2 Answers

My older Coleman Powermate Pulse 1850 is leaking gas from the grommet that connects the hose to the tank. I cannot get needle nose plyers inside the tank to tighten the nut (if there even IS a threaded nut...


I don't think there is any way to tighten or repair leak other then by replacing grommet. sorry I'm not much help but coleman powermate is no longer in business and I have had no sucess in finding a source for parts for you.Thank you and good luck.

Feb 24, 2011 | Coleman 1850 Watts Generator Each...

1 Answer

Want to remove the starter recoil from my powermate generator


I got one of these pieces of junk, and had same problem you described.

You will need to remove the end panel to get to the blower housing. You will have to thread the rope through the handle until you have enough slack to remove the rope from the handle. The end panel should now be free to remove entirely.

Find the 3 bolts that hold the blower housing on, and remove them. Once you get it off, make sure that the rope has a knot in it so it won't get retracted into the pulley recoil assembly. Take a screwdriver and push the rope back down into the pulley (that was my problem). Assembly is opposite of taking apart.

May 23, 2010 | Coleman Powermate Premium Plus 6250W...

1 Answer

Coleman sport 1850 powermate generator, no fire to sparkplug


is there an oilprotection on the gen. disconnect the cable and try again

Jan 18, 2010 | Coleman Sport 1850 Generator

1 Answer

I need to rewind a rope on pull start powermate generator


This requires a bit of strength in the hands and the recoil will have a fair amount of tension behind it. Best have a small engine service center look at. Not expensive

Dec 19, 2009 | Coleman Powermate Generator Start &...

1 Answer

Coleman powermate 1850 charge time


i advice you not to keep it plugged in too long...just about enough to get it workin....
:had a bad over-charge axcident..

Jul 16, 2009 | Electrical Supplies

Not finding what you are looking for?
Coleman Powermate Powermate 5000W Generator Logo

1,055 people viewed this question

Ask a Question

Usually answered in minutes!

Top Coleman Electrical Supplies Experts

John Trevino

Level 3 Expert

1388 Answers

Craig Butler
Craig Butler

Level 3 Expert

1723 Answers

Phil Walker
Phil Walker

Level 3 Expert

608 Answers

Are you a Coleman Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...