Question about Maytag MAH6500 Neptune Front Loading Washer w/Built in Water Heater

2 Answers

Maytag Neptune on/off button wont stay on

I have a Maytag Neptune that the on/off button wont stay on once it is started. Also started leaking water today like it is adding more water than normal and leaks out the front once the tub is filled. It acts like it the timer is out of sync with the cycle. About a week ago it gave off a burning smell. But it stopped and worked fine until today. Any suggestions?

Posted by on

  • Jay Harlow Dec 21, 2007

    Me either. Went and bought me an LG Tromm. I love it. Quieter and It washes a mess load of clothes at a time.

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

We had the same problem on our Maytag Neptune MAH4000AWQ, it turned out to be the controller board behind the control panel. It was about $350 to repair. We are now having problems with the motor not spinning. The repairman offered to sell us the newer model Neptune. Ha Ha. I'm not putting my hard earned money into Maytags hands again. I'd rather by a wash board.

Posted on Dec 21, 2007

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 146 Answers

You have to investigate where the burning smell came from. Start at the timer and then check the main board. Also check the drain pump.

Posted on Nov 05, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Maytag neptune dryer model mde3000ayw wont start


If it only runs with start button held in then you have a problem with the door switch. Check to be sure the wires are on it. Here is the switch to order in case it is bad.

Nov 29, 2012 | Maytag Neptune MDE5500AY Electric Dryer

1 Answer

Why won't my maytag neptune front loading washer will not start?


Check out the door switch to make sure that it closes when you latch the front door. If it does not close the machine will be inoperative - safety measure.

Sep 19, 2017 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Maytag neptune front load washer says control lock and wont start and buttons wont work


unplug the washer for 15 minutes then:plug it back in and, restart a few times in a different cycle canceling each time until the door opens. Do this only if the tub is not full of water if it is let me know and, i'll show you how to drain the washer first before we try to open the door.

Jun 09, 2009 | Maytag Neptune MAH6700A Front Load Washer

1 Answer

My Maytag Neptune leaks water from the bottom (immediately) as it fills with water


usually this is from the front door seal going bad remove the front panel and door to replace it

Apr 30, 2009 | Maytag MAH6700AWW Neptune Front-Load...

1 Answer

Maytag neptune front load washer wont start when button pressed


This is joyce

first lets start simple unplug the machine and leave unpluged for 1 min. replug back, see if this solves the problem.

thanks,



joyce

Feb 06, 2009 | Maytag MAH6500 Neptune Front Loading...

1 Answer

I have the neptune front loader. The lock light wont come on and the door wont lock. During a wash cycle the water just started comming out of the door. If I hold the stop/start button manually the light...


hi there,

you have a door latch problem. the reason you can still push on the button is because this particular washer has a time delay function. i would recommend taking a look at the latch itself and possibly the wax motor that runs the latch.

Dec 04, 2008 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Maytag neptune


i have maytag neptune wash,modelo mah5500bww,my problem is: no starting,flashing start/pause button,after ten minutes is off.And now is ready for start when press start/pause button

May 20, 2008 | Maytag Neptune Washer

1 Answer

Neptune mah4000aww belt wont stay on drive wheel


lost you on chat you closed the window
plz email me

Mar 03, 2008 | Maytag MAH6500 Neptune Front Loading...

Not finding what you are looking for?
Maytag MAH6500 Neptune Front Loading Washer w/Built in Water Heater Logo

244 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

588 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

John Tripp
John Tripp

Level 3 Expert

4655 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...