Question about Microsoft Xbox 360 Console

1 Answer

Three orangish reddish lights

I press the power button and the lights stay blank for about five to six seconds and then three of the lights start flashing an orngish redish color and nothing comes up on the tv screen

Posted by on

  • wolves3eva May 11, 2010

    for this i would recoomend contacting microsoft and see if your console is still under warranty

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 145 Answers

Here is a link from Microsoft to check...
http://support.microsoft.com/kb/907534

However, the 3 red lights usually means the console needs to be sent to microsoft for repair. For this they will normally repair for free. Go to this website and follow directions.

http://support.xbox.com/support/en/us/nxe/LiveIDSignIn.aspx?redirectUrl=http://support.xbox.com/support/en/us/nxe/registerdevice.aspx?step=repair

Posted on May 31, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can I find my AOSS button on my Linksys router


What model?Push the Cisco logo to start SecureEasySetup The logo is lit with a reddish hue (the User Guide says this is orange) when the router powers up in its factory default unsecured state. The instructions say to press the SES button. But there is an approximately 8 second pause between the button push and three seconds of no light, followed by the rapid white flashing backlight that indicates the router is in SES search mode.

Jan 25, 2013 | Linksys Computers & Internet

1 Answer

Extensa 5420 Blank at boot


you have a brand new hard drive... probably cable is not fitted properly and the memory contacts needs cleaning. try it... good luck.

May 19, 2012 | Acer Extensa 5420-5687 Notebook

1 Answer

Playstation 3 wont work it gets to the wavy screen a message says the PS3 was not turner off properly' then i try to restart but nothing happens just a blank screen? Help


Hello

Hello,

Put your PS3 in Standby Mode. The first thing your going to want to know is your model number. It can be found on the back panel of the PS3 on the serial number label, and it will begin with CECH. Example - Serial: XXXXXXXXXXXX-CECHXXX -

For models: CECHA01, BO1, E01, E01MG, G01, H01, H01MG, K01, LO1, AND P01, it will have a power switch on the back. Flip it off then back on and you will have a solid red indicator light on the front.

For models: CECH-2001A and 2001B, press the power button on the front until the indicator light turns red. If all else fails unplug the power cord and plug it back

Time to enter Safe Mode. Press and hold your finger over the power button on the front until you hear three beeps and the indicator light goes back to red. Then release the button. (The second you touch it you will hear a beep, that's the first beep. Five seconds later a second beep, another five seconds the third and final beep will sound then the indicator light will return to red.)

Press and hold your finger over the power button again until you hear a quick double beep. The release the button. (The second you touch it you will hear a beep, that's the first beep. Five seconds later a second beep, another five seconds you will hear the double beep.)

You will then see this screen. "Connect the controller with the USB cable, then press the PS button".

Connect the USB cable to the USB port on the front of your PS3 and the top of your game controller, (between the left and right bumpers). Then Press the PS button in the center of the controller.

You will then see this screen. -REMINDER: -BY DOING THE FOLLOWING ALL OF YOUR DATA ON YOUR PS3 WILL BE LOST, YOUR ONLINE STATS ARE ON THE NETWORK SO YOU WILL GET THAT STUFF BACK, INCLUDING GAMES AND ADDONS YOU BOUGHT FROM THE PSN.-

Select option number 5. (Restore PS3 System). Then select yes to perform step. You will then see this screen. "The hard disk's file system is corrupt and will be restored.

The PS3 will then restart. You will see many different languages, all that is is saying is, "Connect the controller with the USB cable, then press the PS button". Press the PS button and set your settings when it finishes it will start up and its fixed!

I wish you good luck.

Jan 29, 2011 | Sony Playstation 3 (PS3) Console

2 Answers

2005 pontiac astek...changed oil and filter but the change oil light still stay's on for 3 minutes ? how do you reset it ?


Turn the key on,push the accelerator three times slowly with in 5 seconds,and this will reset the oil change reminder,if this was helpful,please rate,and thank you.

Jun 21, 2010 | 2001 Pontiac Aztek

1 Answer

How is it turned on


Press and hold button on face of device for approximately three seconds. Light should begin to flash.

To pair this headset, press same button for approximately five seconds until light comes on and stays on. Locate the device using your handset/phone's Bluetooth operation.

Oct 30, 2009 | LG HBM-710 Wireless Headset

1 Answer

Pushing on power button three green lights come on for one secone


click here you would find the details for led codes. you may select any laptop. codes remain the same.

Sep 24, 2009 | Dell Latitude D600 Notebook

2 Answers

How do I reset my oil light on my 2004 Buick Rendezvous?


Turn the ignition to ON without starting the engine. Fully press and release the accelerator pedal three time in five seconds. If the CHANGE OIL SOON’ indicator flashes two times, the system is resetting. Turn the key to OFF, then start the vehicle. If the CHANGE OIL SOON indicator comes on and stays on for five seconds, repeat the procedure.

Sep 07, 2009 | 2004 Buick Rendezvous

2 Answers

Won't come on


hy i got a toshiba 42" LCD tv ,when i press the power boton
iget the red light,& it stay that way ontil i pressthe power back off
thanks for any help

Jun 26, 2008 | Toshiba 62HM95 62" HDTV

1 Answer

Error code DR


Pull the tech sheet out of the dryer ( behind the lower front access panal ). The lights flashing are trying to tell you a fault code.

A copy:

MODEL DIFFERENCES: • Better models have a digital readout display
• Good models do not have a digital readout display
READING ERROR CODES 1. Position cycle selector knob to the 3 O’clock position.
2. Press and hold the Select and Pause Cancel buttons simultaneously for six seconds.
3. Immediately after, press and hold the START and Pause Cancel buttons simultaneously for 4 seconds.
4. Rotate the cycle selector knob to the 2 O’clock position.
On better model dryers, the error code will appear in the digital display. On good models, the five indicator lights of
Drying, Cool Down, Wrinkle Rid, and Clean Lint Filter Spin will flash the number of times for the first digit of the code
and the START indicator light will flash the number of times for the second digit. Take separate counts of each indicator
light, then repeat to confirm in order to be accurate in identifying the proper error code. The code is obtained by counting
the number of times the lights flash. Example E24: The five indicator lights would flash twice indicating the 2 and the
START indicator light will flash four times indicating the 4. The five indicator lights and the START indicator light start
flashing at the same time. The control will pause for 2 seconds, then repeat the code.
Note: A letter appearing in the code stands for a number higher than nine.
A = 10 B = 11 C = 12 D = 13 E = 14 F = 15
Example Code E4A: the first digit would be 4 and the second digit would be 10. If this code would appear on a dryer in
the Good model line, the five indicator lights would blink four times and the START indicator light would blink ten times.
Troubleshoot problem by using chart below.
To move on to the next code, press the OPTIONS button. To clear code, press the Select button.
To exit this mode, simultaneously press and hold the Select and Pause Cancel buttons for six seconds.

jeff.
__________________
http://www.applianceaid.com/
Appliance Repair Aid
http://www.jrappliance.ca
JRAppliance

Jan 10, 2008 | Frigidaire AEQ7000ES Dryer

2 Answers

3 beeps mean what


If the only thing that happens is three rapid beeps when you select a feature from the console this is usually a symptom of a defective door switch.  The door switch must be closed to complete the circuit from the timer to the heating circuit and drive motor.  If the switch is bad, or the wiring is broken, the dryer will not run.

Oct 17, 2007 | Kenmore 62062 Electric Dryer

Not finding what you are looking for?
Microsoft Xbox 360 Console Logo

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Microsoft Video Game Consoles & Games Experts

marley mcelhinney

Level 3 Expert

490 Answers

Tre Elkins

Level 3 Expert

643 Answers

Martin Murray

Level 3 Expert

1623 Answers

Are you a Microsoft Video Game Console and Game Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...