Ir400 registration problem

The errant handsets must be de-registered from their
original base and then registered to your base.

NOTE: the CS6649 handles a maximum of only five
handsets. If you have a handset displaying
"Handset #5" then you have a 'fully populated system'
even if you actually have only one or two handsets.
In that case, you can clear each handset ( I ) then clear
the base of all registrations ( II ) before re-registering
each handset ( III ) up to the maximum of five.
=====================================
( I ). First, to de-register a handset ---

0. Start by taking off the battery compartment cover.

1. press [menu]
2. scroll up/down to "Settings"
3. enter * 7 8 9 0 #
4. scroll down to "next page", press [select]
5. scroll down to "Register Clear?", press [select]
6. display asks "Confirm?" or "Register Clear??",
press [select]
7. display reads "Ok" and chirps, press [ off ]

8. UNPLUG THE HANDSET BATTERY
(this is why the cover was off)

9. Wait ~30 seconds, re-connect the battery &
replace the cover

10. display reads "Not Registered"
===============================

( II.) To clear the base of all handset registrations
( if needed, else skip ahead to ( III ). )

1. press [Find Handset] on the base and hold
past ~4 sec when the "In Use" lamp lights, at
about 10 secs the "In Use" lamp will begin to
blink. 2. release the [Find Handset] button momentarily,
then briefly press it again. After a moment,
all handsets that were registered to the base
(if any) will display "Not Registered" and be
ready for fresh registration ===============================

( III.) To register each handset to the base:

1. press [Find Handset] on the base and hold for
~4 sec until the "In Use" lamp lights.
2. press # on the handset and set the handset into
the handset cradle on the base
3. within 30 seconds or so, the handset will either
chirp and display "Handset Registered", then
"Handset #x" or it will say "Registration Failed".

NOTE: the battery must be well charged prior to the
registration process, a weak battery may cause a
"Registration Failed". Charge the battery for a
few hours and try the registration ( III ) again.

===============================
Good luck !!

Most likely it's time to replace the drum unit. Mfr Part #: Canon 1342A003AA, GPR-2, F43-6701-700. Those drum units only last 55,000 copies and then the copy quality starts to degrade.

check the button dont ask me again at the time of registration page appear and skip it once that will not appear againg

and there is no need to register the printer

Hi, please get new driver here: www.driversdown.com/
www.nodevice.com/driver/company/Canon/Printer.html
www.usa.canon.com/cusa/office/products/.../hs_1200ts

Jay lwmrt

Did you check the registration clutch? try to clean it. Be sure that the paper drawer sensor is "saying" the correct paper size.

My all-in-one is model C4400. How do I register it?

There is a glitch in the programm, try re-installing driver or updating it

ir400 print e677

power cycle the copier, press the 'print/if' or 'options' button, wait.... "do you want to enter service mode" YES, wait.... scroll down, "clear server", "are you sure?" YES, wait... DONE

the "wait..."'s above can be 2-3 min.
the "do you want to enter service mode" is only displayed for about 10 seconds so watch carefully, if you miss it you have to start over.

One of our Ricoh CL3500N printers- less than a year old- gave us a "color regist error" after changing the transfer belt.

Ran the "adjust color regist" without results. It would just finish and pop back up with the same error.

Color test page printed no color, just BW

I reseated everything, and even replaced the PCU without positive results.

A couple hours later I went back, took everything out (be sure to keep the pcus out of the light!), and vaccuumed the heck outta that printer.

For whatever reason- maybe there was a chunk of toner hanging out, maybe I knocked something loose or back in place, whatever- but when I put all the parts in and turned it on, the error was gone and color printed great!