Question about Raymarine Raychart 435 GPS Receiver

Open Question

Raymarine GPS system HALT ! URGENT PROBLEM

Hello , please we have got this problem. Our GPS Raymarine has run out of its service today and is not working . Since we really need to make it run , we need some help. Is there anything that can be done , when this error messages displays our GPS ??? : Ray Marine GPS system halted code 0x00004001 *addr=0xCOO51DF4* RC435 Chart Plotter This is only thing, that we can get from it , when we turn it on. THANKS A LOT FOR ANY ADVICE greetings from : somewhere between the GREECE islands Hello , please we have got this problem. Our GPS Raymarine has run out of its service today and is not working . Since we really need to make it run , we need some help. Is there anything that can be done , when this error messages displays our GPS ??? : Ray Marine GPS system halted code 0x00004001 *addr=0xCOO51DF4* RC435 Chart Plotter This is only thing, that we can get from it , when we turn it on. THANKS A LOT FOR ANY ADVICE Richard Sweden Gothenburg

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 16 Answers

SOURCE: Raymarine GPS system HALT ! URGENT PROBLEM

To get back up and running you are going to have to reset the unit. This is from the handbook:

Note: Take care - factory reset clears allWaypoint and Route databases.
➤ To perform a factory reset:
1. Power off the unit.
2. Press and hold CLEARwhilst powering up until <Erase backup procedure>
is displayed.
3. Either press CLEAR to abort Factory Reset and resume normal
Power-Up or press ENTER to continue Factory Reset.
4. Press ENTER again; the unit restarts as for a first time PowerUpwith
all values reset to their original factory settings

When you hit port and have an internet connection, make sure you are running the latest software version, currently listed online as version 1.09. You can download it here:

http://raymarine.custhelp.com/cgi-bin/raymarine.cfg/php/enduser/std_adp.php?p_faqid=965

Posted on Dec 28, 2007

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to reconnect a c-80 system. I think the MFD, radar, GPS, and depthsounder are connected via Seatalk


I think your best bet here would be to post your query on the Raymarine forum.

There are actual technicians over there to look after you.

http://forum.raymarine.com/

Hope this helps you out.

Aug 01, 2017 | Raymarine C80 GPS Receiver

2 Answers

C80 GPS


Please remove the power cable form the unit and wait for 30 min then replug it switch on ,,let me if your facing the same problem again...............

Jul 07, 2008 | Raymarine C80 GPS Receiver

1 Answer

How do i set the serial number # on a C120 Raymarine?


you do not set it, but to retrieve it from the menus, go to system menu, system diagnostics, software services, unit info. or it shows during start up sequence

Dec 28, 2009 | Raymarine E120 Multifunction GPS Receiver

1 Answer

Hello! Our Raymarine A65 will not start up. It starts a boot process but does not show "Raymarine A65" on the display and no chart is displayed as it usually does. Regards Odd


Probably a bad printed circuit board, just had to send mine in to have it repaired. When I hit the power button, I did hear a beep, but then nothing displayed. Mine was still under warrenty, so don't know the repair cost if yours is not.

Jul 15, 2009 | Raymarine A65 Combo GPS...

1 Answer

I need a manuel in french


Hi!

You can free download the manual for Raymarine C80 GPS Receiver from the following link---

Raymarine C80 GPS Receiver Manual

Please do accept this solution and revert for further assistance.

Thanks
Rylee

Jul 08, 2009 | Raymarine C80 GPS Receiver

1 Answer

Scanner not reponding - Checking HW


1.try with a new software 4.29
if you have an old one like 2.14 you have a problem.
2. After this try you C 80 on a nother boat or Raymarine dealer
than you will know if the C 80 works

Jun 20, 2009 | Raymarine C80 GPS Receiver

2 Answers

Raymarine SL70 Radar; Unit switches on normally, but there is no radar image appearing. The cable is ok, the scanner is rotating...


I have the same problem. All functions and settings appear to be working OK but no image. After startup time about 3.5 amps are drawm When I turn on power [transmit] amps goes up to 4.5 approx.

I have the scanner head spinning but no target images

Ian

Apr 07, 2008 | Raymarine RL70CRC GPS Receiver

1 Answer

Raymarine GPS system HALT ! URGENT PROBLEM


To get back up and running you are going to have to reset the unit. This is from the handbook:

Note: Take care - factory reset clears allWaypoint and Route databases.
➤ To perform a factory reset:
1. Power off the unit.
2. Press and hold CLEARwhilst powering up until <Erase backup procedure>
is displayed.
3. Either press CLEAR to abort Factory Reset and resume normal
Power-Up or press ENTER to continue Factory Reset.
4. Press ENTER again; the unit restarts as for a first time PowerUpwith
all values reset to their original factory settings

When you hit port and have an internet connection, make sure you are running the latest software version, currently listed online as version 1.09. You can download it here:

http://raymarine.custhelp.com/cgi-bin/raymarine.cfg/php/enduser/std_adp.php?p_faqid=965

Sep 10, 2007 | Raymarine Raychart 435 GPS Receiver

1 Answer

Raymarine rc435


ripoli, This should site should help you now and in the future: http://raymarine.custhelp.com/cgi-bin/raymarine.cfg/php/enduser/std_alp.php?p_sid=8fkbDBti&p_lva=&p_li=&p_new_search=&p_accessibility=0&p_srch=&p_sort_by=&p_gridsort=&p_row_cnt=696&p_prods=&p_cats=&p_pv=&p_cv=&p_search_type=answers.search_nl&p_nav=foot&p_li=&p_page_head=1&p_page=1&p_page_foot=1 Good Luck, Tim

Feb 05, 2007 | Raymarine NMEA 0183 (E55059)

Not finding what you are looking for?
Raymarine Raychart 435 GPS Receiver Logo

Related Topics:

150 people viewed this question

Ask a Question

Usually answered in minutes!

Top Raymarine GPS Experts

Shehu Pro
Shehu Pro

Level 3 Expert

1284 Answers

Steve
Steve

Level 3 Expert

694 Answers

The Knight
The Knight

Level 3 Expert

74459 Answers

Are you a Raymarine GPS Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...