Question about Panasonic Room Air Conditioner CWXC104HU

2 Answers

Hello, I have a error code H16 in a Panasonic air conditioner CS-E12EKK / CU-E12EKK end i want check and I would like tested with a tester the part corresponding to this code Thank You By Advance Ben

Hello, I have a error code H16 end i want check and I would like tested with a tester the part corresponding to this code Thank You By Advance Ben

Posted by on

  • MYMechanical May 11, 2010

    what does the code mean and what part needs testing

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 21 Answers

H16 Outdoor Current Transformer open circuit
• Outdoor PCB
• IPM (Power transistor) module
or try this manual page 21

http://www.hetluften.se/contents/sv/Servicemanual_TE9_TE12_DKE.pdf

Posted on Jun 17, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

Compressor

Posted on Dec 31, 2009

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My linde h16 moves at a very slow pace no matter how much accelerated and it does not show any error code,anyone with a solution?


start off by haveing a compression check to give an idea about the general health of the engine

Jul 16, 2015 | Heavy Machinery

3 Answers

2005 ford Mustang code p2198 is the diagnosis if found on my xcalibrator 2 should I replace the o2 sensor or delete that code and see what happens


Its always a good idea to double check codes especially with sensors, if its the heater circut replace o2 if its out of range reset and see if returns

Apr 05, 2015 | 2005 Ford Mustang

1 Answer

Blue star split 1.5 tr ac eror code e5


The H16 code came on, still does not work machine how to solved H16 error. ???

Jul 02, 2012 | Heating & Cooling

1 Answer

Program manuals ic-h16



  • When you get to the link click on "Click here to start download from MediaFire.." and it will download onto your PC.


  • If you have any comments please feel free to leave them here.
  • Hope this helps and thank you for using FixYa.


Regards, Tony

Oct 05, 2011 | Radio Communications

1 Answer

How to test resistor


HI.You can actually tets a resistor using a MULTITESTER.Set It first to OMHS value.set it to the lowest omhs value.Connecttone end of the tester's to one of te resistor and the other end as well.Now if it gives you a reading a small reading ,itmeans it's not defective and if otherwise it won'T itsdefective the other way around.Now if the reading iss infinite means that TESTERS pointer moves to its maximum,it will also be conidered defective.Esistor has color conding on it.If the reading does not match to its color coding value,then It iS also defective.hope this steps helps you.thank you for choosing FIXYA.

Jul 16, 2011 | Microwave Ovens

1 Answer

To RESET all programs Frequencies on my IC-H16 portable radio.


You can download and review the manual for the Icom IC-H16/U16/U2 HT here. This radio is an Amateur Radio Service transceiver, and will require an FCC license to transmit. No license is required to monitor or listen to the radio. Keep in mind, the Amateur Radio Service is NOT part of "CB" or "FRS" radio services - neither of which require a license to transmit.

When you read the manual, you'll quickly see that there is no "reset" function available. There are only 16 memory locations, so you can simply lock out channels you no longer wish to monitor or you may program any valid frequency in the range supported by the radio. Doing this, in combination with setting the squelch or tone will prevent the radio from opening a particular frequency(s) when the corresponding memory location is scanned.

I hope this helps and good luck.

May 04, 2011 | Motorola GPS

1 Answer

Everytime I turn the receiver on, the fuse inside the unit will burn up and the receiver shuts off.


hello sir..your problem is usually happen when the circuit have shorted parts transistor or even diode...try to test by using multimeter tester range it diode testing for digital tester and for analog range it to ohms..first step is find the base of the transistor.then go for forward testing your tester should got reading after that reverse your test prove if the reverse testing got a reading it means your transistor shorted if not that is in good condition remember when you go for that testing procedure you should remove the parts to the circuit by using soldering iron and soldering pump..thank you

Mar 06, 2011 | Televison & Video

1 Answer

What does error code 130 mean


Hi just read your posting.Error code 130 means you have an error known as SINGLE ROTOR POSITION SENSOR ERROR.This means either the rotor sensor,which is attached to your motor, is faulty or the wiring to the rotor sensor is faulty or your control module is faulty.To test the rotor sensor you need a device called an RPS tester.I can help you check the wiring to the rotor sensor but unfortunately I can not help you test the rotor sensor without you having an RPS tester.Also to help you test the wiring can you borrow or have you got an electrical test meter .Please reply on how you would like to proceed and I will help you as much as I can. Looking forward to your reply.

Sep 13, 2010 | Fisher and Paykel Washing Machines

1 Answer

Beringher CT100.. X Pattern on LED grid when testing an xlr cable


This site has diagrams... not the best but clear enough.

PLEASE note that the pin numbering is kind of goofy... The pins of both the male and female tie to identical pin numbers.

You PROBABLY have misread the numbering at one end.

A KEY thing is to get the shield on pin 1 at both ends.

I recommend that you uncap BOTH connectors, mate them, and verify the same color goes straight across as you solder the wires..

Note: I had some brand new cables delivered that the shield had been connected to pin 3 (middle one) and I had hum ! Note that this defect would NOT be caught by your cable tester as there was conituity between corresponding pin numbers.

May 04, 2010 | Behringer Ct100 Cable Tester

1 Answer

Error code c 26 in toshiba dp 2460


i WOULD CHECK THE EXSPOSURE LAMP AND FUSE FOR LAMP YOU CAN CHECK THIS LAMP BY TURNING THE MACHINE ON AND LOOK AT THE LAMP TO SEE IIF IT LIGHTS UP ON INITIALIZATION IF NOT THE LAMP HAS GONE IF YOU KNOW HOW TO TAKE IT OUT YOU CAN TEST IT WITH AN ELECTRICAL TESTER AT BOTH ENDS OR CONNECTION POINTS

Jun 30, 2009 | Toshiba Office Equipment & Supplies

Not finding what you are looking for?
Panasonic Room Air Conditioner CWXC104HU Logo

Related Topics:

3,507 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Heating & Cooling Experts

Bill Long

Level 3 Expert

588 Answers

Fotis Papastamatiou

Level 2 Expert

109 Answers

Dennis Boxerman

Level 3 Expert

1238 Answers

Are you a Panasonic Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...