Question about Maytag EPIC MFW9700S Front Load Washer

1 Answer

Duet washer stopped during wash cycle.

Whirlpool Duet Washer 9100 (5 1/2 years old) stopped 3 minutes into wash cycle and is flashing the time remaining. Door will open and buttons work but the washer won't start. I tried holding the pause button down for about 20 seconds. I tried turning the circuit off for about 10 minutes but washer did same thing when I flipped the breaker back on. Help!

Posted by on

  • zeringue4 May 30, 2009

    I don't know why this web site posted my question under the Maytag Epic washer section - it's a Whirlpool Duet. How do I move my question?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 56 Answers

Take off the panel below the door three screws and look for the tech sheet located on the right side. It will coach yoou thru the codes and common problems. Sounds like it may be the door swithch does it lock when you push the start? If not the door switch my guess would be a machine control. 877-262-1479 parts.

Posted on May 30, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wash cycle are running to long


FIXED Maytag Neptune, Timer Problem - ApplianceBlog

www.applianceblog.com/.../23387-Maytag-Neptune-Timer-Problem

Mar 4, 2011 - 8 posts - ‎3 authors
My countdown timer is stuck at the 33-minute level in the "wash cycle", and repeatedlyruns for a 30-40 seconds, then stops, then runs, then ... Maytag Neptune TL Washing Machine stops in spin cycle ...
10 posts
Jul 25, 2013
Maytag Neptune Washer Won't Spin/drain
7 posts
Jul 4, 2013
Neptune TL Washer FAV6800AWW - DC and UC ...
5 posts
Jul 3, 2007
MAYTAG NEPTUNE WASHER CONTROL PANEL ...
8 posts
Jun 29, 2005
More results from www.applianceblog.com

Troubleshooting a Too-Long Wash Cycle - whirlpool washingmachine ...

ask.metafilter.com/233920/Troubleshooting-a-TooLong-Wash-Cycle
Jan 25, 2013 - We have a Whirlpool Duet washing machine (about 2 years old). Thecycle is taking WAY too long to complete. The load that's running now ...

Maytag Neptune washer repair: motor/motor control circuit ...

? 12:10
https://www.youtube.com/watch?v=ITTbDh8CFEU
Dec 11, 2013 - Uploaded by daytonaturbofreak
Maytag Neptune washer motor/motor control circuit board ... my board just fried - is your washer still working? wondering how longthe conversion fix will last. ... Other times it will run a completecycle without any malfunctions.

Jan 11, 2016 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

My whirlpool duet washer stops towards the end of the cycle and flashes 6 then F. The door stays locked and the washer beeps. It has happened before, the machine is about 6 years old, how can I fix


F/06

Drive Motor Tachometer Error

The control is unable to properly detect motor speed and the machine will shut down. If a failure occurs during high-speed spin, the door will be unlocked after 3 minutes.

  • Check wire harness connections between the Drive Motor/Tachometer and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU)
  • Check the Drive Motor
  • Check the MCU
  • Check the Wire Harness

Feb 03, 2012 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

During the wash cycle the machine stops and


Hi


Thanks for using FixYa. Error F06 is your whirlpool duet indicates that the control is unable to properly detect the motor speed and so the washer shuts down. This usually occurs during high speed spin and the door will be unlocked after 3 minutes. To resolve this issue you’ll have to check the wire harness connections between the Driver motor and the Motor control unit (MCU). If that is fine then check the connection between the MCU & central control unit (CCU), replace the part that has gone bad. Please do rate the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee

Jul 31, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Whirlpool Duet 9100 will not drain during regular wash cycle. Cleaned drain filter & ran diagnostic and then rinse & drain. Water drained from washer & clothes were damp and I thought the...


I would assume that you are using HE detergent if not the pump could go into a suds lock. You may have a bad drain pump. The other options could be possibly a bad central control unit. (however these are very expensive) or possibly a door lock issue but usually you will get a door lock error.

Jan 13, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Whirlpool Duet Mdl GHW9150PWO Washer stops


HI. this code represents a Long Drain issue.

If the drain time exceeds 8 minutes, the water valves are turned off and F02 is flashed.

Press PAUSE/CANCEL twice to clear the display.

NOTE: After 4 minutes the “Sud” error will be displayed, then 4 minutes later the F02 error code will be displayed.

Potential Causes

• Check the drain hose and make sure it is not plugged or kinked
• Check the electrical connections at the pump and make sure the pump is running.
• Check the drain pump filter for foreign objects
• If the above does not correct the problem replace the pump

Oct 16, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Whirlpool Duet stopped during wash cycle.


UNPLUG THE WASHER AND TAKE THE 3 SCREWS THAT ARE ON THE BACK OF THE WASHER OUT AND REMOVE THE TOP PANEL OF THE WASHER. CAREFULLY UNPLUG AND REPLUG IN THE WIRING SO THAT U WONT GET THEM MIXED UP. DO ALL OF THEM, FIRMLY BUT GENTLY. THEN HOLD IN THE SIGNAL CYLCE LITE FOR 3 SECONDS. TRY TO RUN A LOAD AND SEE IF THAT WORKS. IT DID FOR US, SO FAR SO GOOD. GOOD LUCK!!

May 30, 2009 | Whirlpool Washing Machines

1 Answer

Stops during rinse cycle


Dear customer,

              We recommend the following when a washer's cycles dont advance..
  1. If the washing machine fills with water and begins agitating, but the timer does not advance, the timer probably needs to be replaced
  2. If the timer does not advance while the washer is in a spin cycle, the timer probably needs to be replaced
  3. If the timer does not advance during the rinse cycle, check whether water has filled the tub, if not, it is likely cold water related. Check the cold water supply valve, check the supply hose for kinks, check the filter screen and check the water inlet valve
For details on how to self test these parts plz refer to http://www.acmehowto.com/howto/appliance/washer/washer.php
Plz rate this solution.. thank you.. 

Apr 09, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Washer stopping and flashing F 06 fault


F/06 ---- ERROR IS FOR ----------- Drive Motor Tachometer ErrorThe control is unable to properly detect motor speed and the machine will shut down. If a failure occurs during high-speed spin, the door will be unlocked after 3 minutes.----------
AND TO SOLVE THIS ---------Check wire harness connections between the Drive Motor/Tachometer and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU) --
Check the Drive Motor
Check the MCU
Check the Wire Harness

Apr 02, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Whirlpool frontload duet washer F 6 problem


hello cjkcp
Welcome to Fixya

You said, your washer (now 4 yrs old) occasionally stops mid cycle flashing F 6 code. Is this something we can fix or do I have to call a repair man?

F/06 Drive Motor Tachometer Error

The control is unable to properly detect motor speed and the machine will shut down. If a failure occurs during high-speed spin, the door will be unlocked after 3 minutes.
  • Check wire harness connections between the Drive Motor/Tachometer and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU)
  • Check the Drive Motor
  • Check the MCU
  • Check the Wire Harness

I believe this needs a hands on tech to daignose this. Unless you feel you undrstand the problem your self?

Thank you for using our service for advice.
Please remember to leave a rating!
Huuum

Oct 08, 2008 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Washer stopped during cycle


cleanlaundry If your washer is less then a year old do nothing and call the manufacturer ASAP. It is under warranty for one year. Gendos...post back

Mar 17, 2007 | Whirlpool Duet GHW9150P Front Load Washer

Not finding what you are looking for?
Maytag EPIC MFW9700S Front Load Washer Logo

283 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

587 Answers

John Tripp
John Tripp

Level 3 Expert

4654 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...