Question about Xerox DocuColor 12 Printer

2 Answers

Error codes does anyone know what this means.error code 3-333thanks in advance

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.


    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 56 Answers
Re: error codes

3-333 communications failure between the Foreign Interface
and the machine.
Press 0 and start button at same tame.
Enter 6789 and select confirm. Select dc 131 NVM read/write.
select input number an type:
752-002 0 = Foreign Interface disabled 1 = Foreign Interface Enabled
759-015 1 = Addition Device (Auditron) 2 = Subtraction Device (Debit card)
if you want to see current value select "read"

Posted on Nov 02, 2007

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers
Re: error codes

I am having the toruble shooting manual for the same

Posted on Nov 18, 2007

2 Suggested Answers

  • 56 Answers

SOURCE: error code 9 - 358

Hi,that means ,cleaning auger is stopped.Probably toner waste container is full.Try to remove and replace waste toner container(or vacuum toner from container).

Posted on Feb 20, 2008

  • 212 Answers

SOURCE: Error code 11,009,46:1444 on Xerox Phaser 8500

the 11,009,46 error in my experience means that, at some point, the printer lost power during an electronic action. in some cases an NVRAM reset will do the trick, but if it doesn't, one of the electric boards has been blown up. XEROX are very protective about which board to replace, so you're quite stuck with their own service in order to have it repaired.

Posted on Mar 15, 2011

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

What is error 0xc19a0003 mean for the HP Officejet 4620

ink system failure - error 0xc19a0003 means ink system failure error usually occur if you have issues with your ink cartridge or printheads. Have you try replacing either of the two?

May 12, 2014 | HP Officejet 4620 e-All-in-One Printer,...

1 Answer

I have Canon C3480 had error code E000807-001 what's mean

I have Canon C3480 and had error code E000807-001, anyone know what's mean? thank you. can you email

Mar 05, 2014 | Canon Printers & Copiers

1 Answer

On our Ep3170 we get a C5 error code and the wrench symbol

Hello sir;You must remove the left side panel to access the service switch(s1) on PWB A you press this switch to chose the "C" then enter 0 press "#" ,then press "CLEAR" to terminated.

Jan 17, 2010 | Minolta Printers & Copiers

3 Answers

Error Code E00002-01c0

you probably mean E000020-01c0 bad yellow drum codes in order 01Y 02C 03M 04B

Apr 10, 2009 | Canon imageRUNNER C3200 Copier

1 Answer

Printer Error 09,038.46:3536

That code means the black stick is failing to advance in the printer.
What you want to do is open the area where you load the ink and check your black sticks in particular. The .46 in that code indicates the machine is not detecting the black stick at the borrom of the ink loader. You probably just need to loosten up a stuck block. Sometimes one cracks or gets twisted in the loader.
If you have to remove the blocks take a screw, I use a dry wall type screw to twist into the block and slide them back and out when needed.
You could possibly have a bad sensor in the ink loader, but that is highly unlikely.

Feb 03, 2009 | Xerox Phaser 8560MFP Laser Printer

1 Answer

Xerox Phaser DN error code 09,036,44:2976

Hi, Yep, that's normally an easy one. That code means one of your ink sticks, I think the .44 means magenta, but, one of the ink sticks has not advanced downward properly into the ink loader.
One of the ink sticks has twisted, cracked or otherwise for some reason is not advancing downward into the bottom of the ink loader to melt. Look in there and see where there is a gap. If you need to, take a screw, like a drywall screw and twist that into the ink stick if needed, then slide it back to remove.
If its just stuck then push it down to the proper position.
If you somehow loaded an ink stick for the wrong machine, the different shape will not allow it to actuate the switch at the bottom of the ink loader and will have to be removed.

Aug 12, 2008 | Xerox Phaser 8560MFP Laser Printer

2 Answers

Xerox Phaser 8500N Printer Error

That is a yellow ink stick fault.
One is most likely stuck. cracked or otherwise not advance to the front of the ink loader. Check the sticks

May 27, 2008 | Xerox Phaser 8500/DN Printer

1 Answer

Error code 9 - 358

Hi,that means ,cleaning auger is stopped.Probably toner waste container is full.Try to remove and replace waste toner container(or vacuum toner from container).

Feb 20, 2008 | Xerox DocuColor 12 Printer

1 Answer

Konica Magicolor 5430 DL Fatal Error Code: 0300H

0300H: Polygon Motor malfunction

try restart if not helping then there can be problem with ph unit or PWB-A board

Sep 11, 2006 | Konica Minolta magicolor 5430 DL Laser...

Not finding what you are looking for?
Xerox DocuColor 12 Printer Logo

Related Topics:

249 people viewed this question

Ask a Question

Usually answered in minutes!

Top Xerox Printers & Copiers Experts


Level 1 Expert

185 Answers


Level 2 Expert

110 Answers

Patrick Carmichael...
Patrick Carmichael...

Level 2 Expert

107 Answers

Are you a Xerox Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides