Question about ASUS WIRELESS ROUTER |WL-520G - RT (WL520G)

1 Answer

I cannot connect to the internet but network is working...

I already configured my new asus wireless router and my network is already working but i cannot connect to the internet.. i have connected with the asus network but couldnt brouse the internet

Posted by on

  • George Day May 11, 2010

    Is your ISP cable or DSL?

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 63 Answers

What is the wan IP in your modem?
What is your DNS configuration?
Cna you successfully run the following command from a command prompt?
nslookup google.com
Does it resolve the hostname to an ip address?

Posted on May 30, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can i find out my encription code for my asus eeepc


The encryption code is in your router's wireless setup.
To connect your computer to a wireless router, you click the Refresh network list, then Choose your wireless network and then click Connect to your secured Wireless Network, it will asks for a Network Key before allowing you to connect into your wireless network. This Network Key is either the WEP, or WPA or WPA2 Encryption key that is configured in the Wireless settings in the Router. The Passphrase is an alternate way to setup the Encryption key.
When you are requested for a Network Key, you can just enter the Passphrase or WPA or WPA2 key that was used to configure the Encryption key in the wireless router. http://www.fixya.com/support/r5270415-network_password_network_address For information on securing your wireless network, configuring the wireless router and configuring the wireless card in the laptop/computer, please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

Mar 28, 2013 | ASUS Eee 4G Notebook

1 Answer

My desktop PC is currently connected to the Internet wirelesly without a problem. Also my notebook ASUS N61Jv has connection to the Internet but only by wire. I wish to have access to the internet...


The router's password is a Passphrase or the WEP or WPA orWPA2 encryption key. The Passphrase generates the WEP or WPA or WPA2 encryptionkey and this is in the router's wireless settings. To connect to your wireless router, it needs the router'swireless settings configured ie SSID, WPA or WPA2 encryption key and also thewireless cards in all the laptops and or computers needs to be configured withthese router's wireless settings. Then the laptops and desktop computers cancommunicate with your wireless router.

Mar 11, 2011 | Computers & Internet

1 Answer

How to conect with wireless internet


The Network and Sharing Center in Microsoft* Windows Vista* can be used to set up a secure wireless connection to the Internet.

Note: If an Internet connection is not automatically made by the operating system, you may need to contact your access point (AP), broadband wireless router manufacturer, or Internet Service Provider (ISP).

Set Up a Secure Wireless Connection to the Internet


These steps assume that your network adapter; AP or router; and cable, DSL or another type of modem have already been physically connected and configured. They allow you to create a new connection and configure it accordingly.

Follow these steps to set up a secure wireless connection to the Internet.

Note: If a wireless profile does not exist, you will need to create a secure wireless profile before you can set up a wireless connection to the Internet.

1. Access the Network and Sharing Center.

2. Select Set up a connection or network.

3. Click Connect to the Internet.

cs025389_selectanetwork_configurationnotmatching.jpg

4. Click Next.

5. Select Wireless. At this point, if the network(s) that are listed say that the network settings do not match the network requirements, as shown in Figure 1, create a secure wireless profile and then follow the steps again.

6. Select a network and click Connect. If you are not connected to the Internet, you may need to contact your AP/router manufacturer or ISP.

Access the Network and Sharing Center


To access the Network and Sharing Center, use one of the following methods:
  • Start » Control Panel » Network and Internet » Network and Sharing Center
  • Start » Network » Network and Sharing Center
  • Right-click the network system tray icon (the icon that displays two computer monitors) » Network and Sharing Center


Jan 21, 2011 | Computers & Internet

1 Answer

Can't get my lap top to connect wirelessly to my router. Model # WRT54G2. The laptop says it is reaquiring the network address, but nothing happens.


The Network and Sharing Center in Microsoft* Windows Vista* can be used to set up a secure wireless connection to the Internet.

Note: If an Internet connection is not automatically made by the operating system, you may need to contact your access point (AP), broadband wireless router manufacturer, or Internet Service Provider (ISP).

Set Up a Secure Wireless Connection to the Internet


These steps assume that your network adapter; AP or router; and cable, DSL or another type of modem have already been physically connected and configured. They allow you to create a new connection and configure it accordingly.

Follow these steps to set up a secure wireless connection to the Internet.

Note: If a wireless profile does not exist, you will need to create a secure wireless profile before you can set up a wireless connection to the Internet.

1. Access the Network and Sharing Center.

2. Select Set up a connection or network.

3. Click Connect to the Internet.

cs025389_selectanetwork_configurationnotmatching.jpg

4. Click Next.

5. Select Wireless. At this point, if the network(s) that are listed say that the network settings do not match the network requirements, as shown in Figure 1, create a secure wireless profile and then follow the steps again.

6. Select a network and click Connect. If you are not connected to the Internet, you may need to contact your AP/router manufacturer or ISP.

Access the Network and Sharing Center


To access the Network and Sharing Center, use one of the following methods:
  • Start » Control Panel » Network and Internet » Network and Sharing Center
  • Start » Network » Network and Sharing Center
  • Right-click the network system tray icon (the icon that displays two computer monitors) » Network and Sharing Center

Jan 10, 2011 | Linksys Wireless-G WRT54G Router

2 Answers

I am trying to install a Netgear router after my switch. I end up having no internet on some of the computers connected to the hub and none on the router. If I configure the router as a dhcp client...


You'll want to configure your router as a dhcp server. Connect the switch to your router's lan port. Connect the remaining devices to a port on the switch. Your wireless access point should have it's dhcp server disabled. You can only have one dhcp server per network. The wireless can get it's address from the router's dhcp and the wireless client devices will get their ip address from the router, as well. If your wireless access point is a router with a wan/broadband port and some switch ports you will want to make sure that you are connecting to your Asus switch via one of the switch ports.
Be sure that your client devices are configured to get their ip address via dhcp and you should be surfing the interweb in no time flat.

Oct 21, 2010 | ASUS GX1008B 10100Mbps Desktop Unmanaged...

1 Answer

Unable to make router wireless


To use a wireless network/connection you need to do.
1. Configure the router's wireless with SSID, WPA encryption etc.
2. Next configure the wireless card in the computer/laptop with the router's wireless settings so it can connect to the wireless router.
Please click on this link for my instructions on how to secure your wireless network, configure the wireless router and configure the wireless card in the computer/laptop :-

http://www.fixya.com/support/r3559128-wireless_router_security

Feb 10, 2010 | 3Com Computers & Internet

1 Answer

Hi, I have an old acer laptop and my wife communicates with me on it using broadband and a router with a usb pick up. I have returned home and have a new acer laptop with wireless LAN already installed. It...


Youe broadband router is working ok with the broadband cable.So it is configured with the broadband cable.Now,to work with the wireless internet,you have to configured the wi-fi router to work internet.You can see the wi-fi connection but unless & untill you will configure wi-fi router it must not work or if before it was working with the wi-fi then you can check the wi-fi router setting because it might change by mistake.Surely it will work after configurating wi-fi router.

Jan 03, 2009 | Computers & Internet

2 Answers

I cannot connect to the internet but network is working...


did you config the router as an access point?

does the internet work when you by pass the router?

Dec 21, 2008 | ASUS WIRELESS ROUTER |WL-520G - RT...

1 Answer

Connecting 2 routers (ASUS WL-500W and D-Link DSL-G604T Wireless)


This will give you a "Double NAT" setup. Meaning, Your D-Link router is connected to the external internet address assigned to you by your internet service provider. More than likely this is a DHCP address you do not control. Your D-Link router is then translating the address to the 192.168.1.x network. This is the first NAT translation. You are then connecting the ASUS router to DLINK, causing a second NAT translation. (Internet ADSL --> D-Link WAN Port --> D-Link Lan Port --> ASUS WAN Port --> ASUS Lan Port to computer/server/etc. ) If both of your routers are giving out DHCP addresses, then this is all that is required.

Nov 22, 2008 | ASUS WL-500W Router (WL500W)

1 Answer

WUSB300N


This would most likely happen if your router is not configured to connect to the modem correctly. You said that you can connect to the router locally that means there is already a connection. The problem would be the routers configuration to the internet.

Jul 15, 2008 | Linksys WUSB300N Wireless Adapter

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

387 people viewed this question

Ask a Question

Usually answered in minutes!

Top ASUS Computers & Internet Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18424 Answers

Alun Cox

Level 3 Expert

2678 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Are you an ASUS Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...