Question about Roland GX-300 CAMM-1 Pro Vinyl Cutter

Open Question

Cutter is skipping areas when cutting

Doesnt cut clean and makes weeding impossible

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

One or more of your cut images are not positioned entirely on the mat, They will be skipped


Just follow the steps given at this link, and your cutter should begin to cut again. I just tried it and my cutter is back cutting. Cricut Craft Room Troubleshooting Cricut Help Center

Aug 01, 2016 | Provo Craft Cricut Mini Electronic Cutting...

1 Answer

My ryobi 30cc grass cutter model rtp 3000 runs but no power to cut gass


I have seen the flex cable broken between the power head and the cutter head .

Feb 20, 2016 | Stihl FS 85 Weed Eater

1 Answer

Put too much oil in the Husqvarna brush cutter. It smoked the first 30 minutes of use, then died and now will not start. Did I ruin it. What needs to be cleaned or checked. It uses straight gas.


You state you put too much oil in the cutter. then you state it uses straight gas. All the cutters I ever used had a mix of 2 cycle oil and gas. Usually when you place too much oil in the mixture it fouls the spark plug and could cause carbon build up. If the plug has oil on it it will never ignite. Do not put straight gas in the fuel to try to burn off the oil you will only make matters worse. Clean the plug, drain your fuel and start from scratch. If it still fails to start, you need to bing it in to a small engire repair shop. Good Luck!!

Aug 11, 2014 | Garden

1 Answer

Automatic thread cutter.bobbin thread does not feed to the top.


when you stop sewing where is the arm located ,up or down ..that will make a world of difference

Jan 06, 2014 | Elna 7200 Computerized Sewing Machine

1 Answer

Cutter runs for approx 10- 20 min and cut off and have to cool down before it starts again.


Hi, have you ever cleaned the unit out? If you have air pressure available, this is the easiest way to do it. Blow all the old dead grass, weeds ect out from the engine area of the Weed eater. If you don't have or have access to a compressor, take the unit to your local garage/service station and ask to use their air, or ask them to blow it out for you. This alone may cure the problem. However the proper mix is critical for proper performance also. If the mix is too lean the unit will over heat. Clean it out, and be sure of the mix ratio. You should be 'good to go'. Good Luck Vern

Jan 30, 2012 | Stihl FS 85 Weed Eater

1 Answer

My plasma cutter wont cut on cars


Like an other welding job - be sure the grounds are clean and secure. Ground as close to cut as practical and if trying to cut painted area - remove paint for good ground and to cut down on fumes from burning/melting paint. Disconnect battery as well so as not to bachfeed any voltage into your electrical system. IE ecm - computer

Dec 01, 2010 | Welding Tools

1 Answer

Change cutting line


Pop of bottom cover and wrap new line by turning head or replace with different spool or blade cutter

Jul 01, 2009 | Craftsman 22" Gas Hedge Trimmer

2 Answers

Plasma cutters Question


There are a few things about plasma cutting safety that are different from general welding safety tips This short list of plasma cutter safety tips is geared toward light duty plasma cutting using compressed air not large industrial units that use gas mixtures and water cutting tables. Electric Shock Can Kill - Operating a plasma cutter completes an electric circuit between the torch and the workpiece. The workpiece and anything touching the workpiece are part of the electrical circuit. - Never touch the torch body, workpiece or the water in a water table when the plasma system is operating. Voltages & Currents - Plasma cutter output voltages are much greater than welding voltages, usually 100-200 volts. Precautionary Measures - Do not pick up the workpiece, including the waste cutoff, while you cut. Leave the workpiece in place on the workbench with the work cable attached during the cutting process. - During plasma cutting operations do not move the work clamp. Wear insulated gloves and boots, and keep your body and clothing dry. - Do not stand, sit or lie on or otherwise touch any wet surface when using the plasma cutter system. - Insulate yourself from work and ground using dry insulating mats or covers big enough to prevent any physical contact with the work or ground. If you must work in or near a damp area, use extreme caution. Work Cable - Ensure metal-to-metal contact between work cable and workpiece or work table. - Work cable clamp should make contact with clean metal free of rust, dirt, painted surfaces, etc. - Do not attach work cable to the piece that will fall away when the cut is complete Plasma cutter Arc Rays Plasma cutter arc rays produce intense visible and invisible (ultraviolet and infrared) rays that can burn eyes and skin. Protective Clothing - Guantlet gloves, safety shoes and hat. - Flame-retardant clothing to cover all exposed areas. - Cuffless trousers to prevent entry of sparks and slag. - Remove combustibles, such as a butane lighter or matches, from your pockets before cutting. Noise Levels of Plasma Arc Cutting - Plasma arc cutting systems can generate noise levels in excess of 120 dB during high-amperage cutting operations. - Ear protection should be used when operating or working near plasma arc cutting operations. Toxic Fumes & Gases Plasma arc cutting can produce toxic fumes and gases that deplete oxygen and cause serious injury. - Keep the cutting area well ventilated or use an approved air-supplied respirator. - Do not cut in locations near degreasing, cleaning or spraying operations. The vapors from certain chlorinated solvents decompose to form phosgene gas when exposed to ultraviolet radiation. Pacemakers & Hearing Aids - Pacemaker and hearing aid operation can be affected by magnetic fields from high currents. Pacemaker and hearing aid wearers should consult a doctor before going near any plasma arc cutting and gouging operations Overall Plasma Safety - The plasma arc cutting process can be very safe. - By paying attention to safety standards and correctly setting up and operating the system, plasma arc cutting poses no more a threat than most welding processes.

Aug 27, 2008 | Miller Spectrum 375 Cutmate Plasma Cutter...

Not finding what you are looking for?
Roland GX-300 CAMM-1 Pro Vinyl Cutter Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Roland Office Equipment & Supplies Experts

JonSnell Electronic
JonSnell Electronic

Level 3 Expert

29841 Answers

Ravi

Level 3 Expert

1682 Answers

Are you a Roland Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...