Question about GE Vacuums

1 Answer

Suction stopped working immediately

My vacuum is not suctioning at all. it was working last week. it just leaves stripes on the floor. it's bagless but the dist compartment is clean and the floor brush is also clean. in fact, when turned upside down, it almost seems as if it is slightly blowing out instead.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 50 Answers

There is a hose on the unit. Disconnect it at both ends. Stretch it out. Look down it. If you can't see down it, rod it out.

Posted on May 28, 2009

  • Douglas Jones May 28, 2009

    There is a hose on the unit. Disconnect it at both ends. Stretch it out. Look down it. If you can't see down it, rod it out.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where do you put attachments to make them work?


There is a button on the handle that releases the suction tube from the floor brush housing. Once the suction tube is released from the brush assembly, you can install the attachments on the suction tube.

Nov 15, 2015 | Dyson DC14 All floors Bagless Upright...

1 Answer

No suction at floor section only on hand held part


clean the hoses and any part connecting the actual vacuume to the floor attachment.... probably clogged or not getting a good seal....if the motor sounds like its going faster (higher pitch) then its clogged up.....

Nov 09, 2013 | Russell Hobbs 14835 Tornado Stretch...

1 Answer

Poor wand suction


your cyclone assembly may need to be striped down and cleaned also remove the exhurst filter located under the bin.

Oct 15, 2013 | Dyson DC17 Animal Bagless Upright Cyclonic...

1 Answer

No suction


Sucked up a sock?? No seriously.. it may be as simple as that or that an on board filter is clogged. Check your manual for all filters and Hepa/screens and others. Also, is the unit making any odd noises since the non -suction scenario? Whining or screeching sounds, where is the motor impeller/vac bearing or similar is damaged or a hose is kinked within hte unit itself.. <not normally unless the unit has been taken apart and placed back together and crushed the main return vac hose. .

Apr 30, 2010 | Dyson DC14 All floors Bagless Upright...

1 Answer

Dyson DC 25 Ball - no power to motor


Same problem here. We noticed a loss of suction for about 5 minutes and the suction stopped. Beater bar still rotates but ZERO suction.

Mar 14, 2010 | Dyson DC25 All Floors Bagless Upright...

1 Answer

Not picking stuff up and no suction in hose as well, suction sounds good until you go to vaccuum floor


Because this unit is bagless there are more gaskets to seal the suction portion of the vac. you are most likely missing a seal, can you remove the basket and place your hand near the suction on the vacuum? it is shielded so you wont lose fingers. if there is suction there, look at the bottom of the basket for a gasket, same for the top

Jan 01, 2010 | Dyson DC14 Animal Bagless Upright Cyclonic...

1 Answer

Vacuum won't **** in upright position, but there is suction from the hose in the upright position


theres a knob that switches it from floors to carpet turn the to floors.please leave feedback

May 03, 2009 | Vacuums

1 Answer

No suction on Hoover Wind Tunnel.


Greetings from GoVacuum.com,

First this is a common problem on ALL bagless vacuum cleaners. Usually it takes longer then 1 day however.

Is there no suction in the suction hose, or is it not suctioning from the floor?

Most people buy a bagless vacuum once, then return to a bagged one after their bad experience, you are not alone!

Please give me the model number to your Hoover, (found on the bottom or the back of the vacuum on a foil label).

Thanks,

Chris Jones
GoVacuum.com
1-866-468-2288
chris.jones@govacuum.com

Aug 18, 2008 | Vacuums

1 Answer

Bissell clearview bagless upright


Hi.

Is this machine a Dyson or Bissell & what model number. ?

http://dysonmanuals.llc.nu/

Chris.

Feb 27, 2008 | Dyson DC07 Bagless Upright Cyclonic Vacuum

Not finding what you are looking for?
Vacuums Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Vacuums Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1460 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18391 Answers

ray gallant

Level 3 Expert

42945 Answers

Are you a GE Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...