Question about Northwestern Bell 36280-1 2.4 Ghz Cordless Phone

1 Answer

Can,t call out ,just get beeping

When i try to call out it says not activated . Everything else is showing fine . Had this problem before but lost my book so can,t remember what to do .

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 77 Answers

Place the handset on the base then try to dial the number. If it works then you will need to pair your handset with the cradle again before taking the handset away from the cradle to dial a number

Last resort unplug the power for five minutes and power on the base again.

Posted on May 30, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a fisher & paykel active smart fridge the fridge part freezes everything and wont stop beeping when door open


Your fridge is telling you there is a fault, i'd say one of the 2 fans are not working. If everything is freezing in the bottom of the food compartment then the upper fan is faulty. You have to remove the shelves & remove the rear panel, the fan is in the shute at the bottom, remove, repair the broken wire or replace. Make sure unit is unpluged.

Aug 10, 2014 | Fisher and Paykel Active Smart E522B...

1 Answer

Computer turns on but I get a no signal sign on the moniter


If your computer has a video card try connecting the monitor to the motherboard video.

Mar 14, 2013 | Dell OptiPlex GX620 PC Desktop

1 Answer

Just moved into a foreclosed house with a GE security system and no manual. We never received the code, which was fine since it wasn't activated. However, when we lost power in a thunderstorm, the...


Is there a phone number on the control panel?
Is there a backup battery that may need to be replaced?
If there is any contact information available, call to get the manual, etc.
Gary

Jul 02, 2011 | Vacuums

1 Answer

I have a Westinghouse RV525V-R*4 Virtuoso Fridge (Electronic Display) which beeped twice and gave an error today on the display - Cnn Err. The dispay was showing the temp in degrees F. Tried everything...


I wasn't keen on the 48hr period so I tried a work around. I disconnected the front display which reset the alarm in question. To disconnect the display you have to disconnect the wires that supply this power. This is located underneath the top plastic hinge cover for the freezer. Remove the cover

May 31, 2011 | Westinghouse Refrigerators

1 Answer

We can't activate the stylus. When our last estimatr was here everything worked fine. As soon as we went to use after he left we couldn't get to work. Any ideas?


Plug in the Digitizer and make sure you hear four (4) beeps and 4 beeps only.
Any other tone would indicate a problem.
If you get four beeps,try to set the Superset code to S01 by using the stylus,select S,then 0 then 1 and you should hear four beeps again.
If this doesn't work the pen may have gone bad,have an open wire inside the cable.
It would have to be replaced. If you have another transducer,pen or cursor,try those.

Aug 30, 2010 | GTCO Quik-Ruler Digitizer, 36/48" (QR3648)

2 Answers

Dell Monitor Power save mode activate using pc


yes right click on desktop select properties then click on screen saver then increase wait time problem will solved

Oct 29, 2008 | ViewSonic VE155b 15" LCD Monitor

1 Answer

One beep activated


Go to Settings > Sound > Volume > Master Volume > It should say "One Beep". Then press the right arrow button and it will change settings. Change it to the Level volume option. You should have your sound back.

Mar 17, 2008 | Lands Phones

1 Answer

Help with connecting to wireless network


right now i am using someone elses computer while i am trying to fix mine. I am using a wireless card. All signals are good and everything shows connected but when it shows the sent and received activity there is a number for the sent activity and a 0 for my received activity what is causing this.

Mar 05, 2007 | HP Pavilion ze4125 Notebook

Not finding what you are looking for?
Northwestern Bell 36280-1 2.4 Ghz Cordless Phone Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Northwestern Bell Lands Phones Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Computer Repairing
Computer Repairing

Level 3 Expert

14641 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Northwestern Bell Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...