Question about Crosley CDE6000 Electric Dryer

1 Answer

Crosley Electric dryer stopped in mid cycle and will not start

Crosley Electric dryer stopped in mid cycle and will not start

Posted by on

  • dalovell May 27, 2009

    Crosley Electric dryer stopped in mid cycle and will not start.
    We checked - we have power to dryer.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 91 Answers

If the machine is completly dead an not doing anything locate your fuse panel ,check your fuses for the dryer ,if you can find wich one is it reset the breakers again you probably popped one of the 2 lines since you need 2 for a 220v.

good luck!

Posted on May 27, 2009

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 56 Answers

SOURCE: Crosley Electric dryer stopped in mid cycle and will not start

unplug unit raise lid by putting putty knife under right and left front edges about an 1 1/2 in on each side. push the knife in to realease the spring clip on each side, look at the heating element in the center back on the right had side of the element case is a small thermal limit that has two white wires coming off of it. to get it out take out the 1/4 in srew that holds the element down, also take off the safety limit switch about the element with the two red wires on it. lift out element slowly you will have to work it out so as not to damage then look inside and see how the limit switch is attached pull out and ohm out or take to service center and buy it should be an LA1053 kit put all back together then try again. you may be able to get it out without removing element also but removal of the element makes it easier.Also take the screw out of the left side and right side that holds the front on about 2 inches down on the inside of panel on each side. look for lint in blower housing on door clean well and clean area where lint screen is housed. i then you should also check your dryer vent it may be plugged up since it blew a thernal limit safety.

Posted on May 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dryer drum stops turning mid-cycle


The belt may be in need of replacement.

Dec 02, 2013 | Frigidaire GLEQ2152ES Electric Dryer

1 Answer

Kemore 65962 stops mid cycle


The circuit panel could be at fault

Mar 26, 2013 | Kenmore 659 Electric Dryer

1 Answer

My dryer has been difficult to start lately especially if stopped mid cycle. The lights are all on but it won't start up. Today I only used it 2 times and it was very difficult to start after pressing many...


You may be experiencing "Heat Retention" by stopping your dryer mid-cycle, which you should NOT ever have to do! If you have a minor vent restriction or if you open the dryer mid-cycle when the heat is on, this will cause a disruption in the airflow and rising temperatures can keep the dryer from restarting until it has been cooled long enough.
Check your vent all the way to the outside for restrictions/obstructions every 6 months. Clean your lint filter after each load and DO NOT stop the dryer mid-cycle!
Note: Stopping the dryer mid-cycle can also cause severe burns and even melt polyester fibers.

Jul 05, 2009 | Maytag Neptune MDE5500AY Electric Dryer

1 Answer

Dryer stopped in mid cycle.


Sounds like you might need a new motor.

Mar 06, 2009 | Kenmore 62602 Electric Dryer

1 Answer

Whirlpool gas dryer stops in mid cycle and then starts up again


make sure of mode# make inside door and I will help you. also how old is your drier?

Feb 01, 2009 | Whirlpool LER4634J Electric Dryer

1 Answer

Dryer won't start


check door switch..onthejob

Jan 27, 2009 | Crosley CDE6000 Electric Dryer

1 Answer

Crosley dryer


Let the machine sit for about an hour and try again. Let me know what happens. Would like to know the reason the motor was replaced.

Jan 26, 2008 | Crosley CDE6000 Electric Dryer

1 Answer

Pressing door switch makes dryer stop...why?


The door safety switch has come loose or become misaligned. A little study will reveal how the switch works, & most likely why it doesn't. There should be a obvious way to adjust the switch, or call an appliance tech to do it for you. Unplug the dryer before attempting to work on this switch, as high voltage may be present.

May 17, 2007 | Crosley CDE6000 Electric Dryer

Not finding what you are looking for?
Crosley CDE6000 Electric Dryer Logo

Related Topics:

358 people viewed this question

Ask a Question

Usually answered in minutes!

Top Crosley Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Tim Whalen

Level 3 Expert

3072 Answers

charles

Level 2 Expert

97 Answers

Are you a Crosley Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...