Question about Car Amplifiers

2 Answers

Helppp how do u put on a serpentine belt on my 1995 pontia c sunfire

Posted by on

2 Answers

Re: helppp

Change everything between the license plates. That thing is a P.O.S

Posted on Nov 04, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 709 Answers
Re: helppp

You should have a Diagram on the Radiator cowling.  Thread the Belt as posted in diagram.  Leave the belt on all pulleys but the Altenator Pulley.  Use a wrench on the Tensioner to give your Belt anough slack to roll it onto the Altenator pulley.  Your Done.  Your Jack kit in the trunk may have a tool for wrenching the Tensioner Pulley.  

Posted on Oct 23, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Cassette Player

It could need a good cleaning. It could also be a broken belt.

Apr 12, 2014 | Dual Jeep Wrangler Yj 87-95 10" Subwoofer...

1 Answer

Wiring diagram for 1995 lincoln mark 8 lsc stereo

I would recommend a Chilton/haynes manual for $20 at any local auto parts store

Dec 01, 2009 | Car Amplifiers

1 Answer

I have a 1995 Grand Jeep Cherokee Larado I'm putting in an after market stereo. It has an infinity gold system and amplifier. I can't get any sound out of it and can't figure out which wire to connect the...

a good way to find out is, if your lucky- you still have the plug connected to the wires in your dash. Buy a wiring harness from a place like Best Buy. The harness, when plugged in to your factory harness will have its blue wire in line with the factory amp wire. There also may be a Blue wire with white stripe, this also needs to be connected to the blue wire if the above doesn't work. If you dont have a factory plug anymore- bigger problem.

Sep 05, 2009 | Car Amplifiers

1 Answer

Toyota corolla 1995 sterio fuse proublem

Trying replacing the radio fuse under your dash. You have blown the radio fuse, and I believe the dome light is on that fuse as well.

Feb 04, 2009 | Sony Xplod XM-554ZR Car Audio Amplifier

1 Answer

Radio Reset codes

go to any of that makers dealerships and they will take the serial number and put it in computer which will then give them your unlock code. usually costs about £20.00

Jul 07, 2008 | Car Amplifiers

1 Answer

Trying to put in a sterio in a bmw325i

1995 BMW 325 Stereo Wiring Constant 12V+ Red/White Switched 12V+ Purple/White Ground Brown Illumination n/a Dimmer n/a Antenna Trigger White Antenna Rear Window, Diversity Front Speakers 5 1/4" Kick Panels Left Front (+) Yellow/Red Left Front (-) Brown/Orange Right Front (+) Black/Red Right Front (-) Brown/Orange Rear Speakers 4" Rear Deck Left Rear (+) Yellow/Black Left Rear (-) Black/Orange Right Rear (+) Blue/Black Right Rear (-) Brown/Orange

Jun 08, 2008 | Pioneer Car Amplifiers

1 Answer

Seat Belt Chime

Belt Minder Deactivating/Activating


1. Before deactivating/activating the belt minder, set the parking brake.
Place the transmission range selector lever in P (PARK) (automatic transmission) or the NEUTRAL position (manual transmission).

2. Place the ignition switch in the OFF position.

3. Close all the vehicle doors.

4. Unbuckle the driver safety belt.

5. Place the parking lamps/headlamps switch in the OFF position.


1. Turn the ignition switch to the RUN position. (Do not start the engine.)

2. Wait until the safety belt warning lamp turns off (approximately one to two minutes).

3. NOTE: Steps 3 through 5 must be completed within 60 seconds or the procedure must be repeated.

Buckle then unbuckle the safety belt nine times, ending with the safety belt unbuckled. This portion of the procedure can be done before or during belt minder warning activation.

4. Turn the parking lamps/headlamps ON then OFF.

5. Buckle then unbuckle the safety belt nine times ending with the safety belt unbuckled. After this step the safety belt warning lamp will be illuminated for three seconds.

6. Within seven seconds of the safety belt warning lamp turning off, buckle then unbuckle the safety belt. This will enable the belt minder if disabled or disable the belt minder if enabled.

7. The following sequence of events confirm the belt minder is enabled:

-flashing of the safety belt warning belt lamp four times per second for three seconds

-three seconds with the safety belt lamp off

-flashing the safety belt lamp four times per second for three seconds again

8. The safety belt lamp flashing four times per second for three seconds provides confirmation that the belt minder is disabled.

9. After confirmation, the deactivation/activation procedure is complete. user_offline.gif

Apr 02, 2008 | Car Amplifiers

Not finding what you are looking for?
Car Amplifiers Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Car Amplifiers Experts

Tygh Duval
Tygh Duval

Level 2 Expert

290 Answers

Pablo Gonzalez

Level 3 Expert

733 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Car Amplifier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides