Question about Adtran NetVanta 3200 Router

1 Answer

Netvanta reset password

I have a netvanta 2050 that needs the password reset. the wan addresses have changed/How do I clear the current password.Stedman Stewart

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 83 Answers

Enter admin as the username, enter your admin password, and click the OK button. (The default password is
password.) Here is a link to your manual:

http://www.wedophones.com/Manuals/Adtran/NetVanta%202000%20Series%20Quick%20Start%20Guide%20(Rev%20B)%202nd%20gen.pdf

Posted on May 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Silkworm 2050


Hello, do you need to reset it because you no longer have the password? Sorry about the question however that is one of the most common reasons for folks attempting to do a "factory restore". If it is for a lost password, then my next question would be what firmware version are you running? I'm guessing it is something like FOS v2.6.x. If that is the case then the bad news here is you will need to obtain the Password Recovery firmware from your switch support provider. I say bad news because given the age of the SW 2050, this is probably no longer possible. You might give Brocade Support a try at one of the numbers listed on the following page: http://www.brocade.com/services-support/international_telephone_numbers/index.page.

If you have another need for the factory reset, reply back with those details. There isn't a factory reset button but perhaps we can look at different commands to achieve what you need to clear.

May 08, 2014 | Brocade Communications Systems SilkWorm...

1 Answer

Josephine123


1.Press and hold the reset button on the back of your wireless router
2. Connect a computer to one of your router's Ethernet ports (but not the one that says WAN)
3. In the browser address bar, enter the IP address of your router's administration interface
4.Enter the default administrator login name (usually "admin") followed by the default administrator password.
5. Click on the "Admin" page from your router's configuration page and creat a strong password

Checkout here for m,ore networking accessories at cheap pices online.,
http://www.gizga.com/consumer-electronics

Jan 06, 2014 | Computers & Internet

1 Answer

Changeing Password on Router


First, you'll need to reset the router, this is typically done via a tiny reset button located on the back of the router (you'll need a paper clip to press it). After that, changing the password requires you to know how to access the router options. This is different from brand to brand, but typically by simply going onto Google and searching for your modem's address (might be an IP address or actual address, like linksusrouter). Then just go into the settings, find the "change password option" and viola.

Oct 09, 2012 | Westell Versalink 327w Wireless Modem...

1 Answer

I do not know the password to acccess adtran 3430 router. how can I reset the router to reconfigure


Thank you for using FixYa
The default password is 'password' and then 'admin'
uaafqqavnaaaaaelftksuqmcc
http://docs.google.com/viewer?a=v&q=cache:2jM0LFDsYpEJ:www.andovercg.com/datasheets/adtran-netvanta-3430.pdf+Adtran+Netvanta+3430+Router&hl=en&gl=us&pid=bl&srcid=ADGEESj5spjwkyVJC6UyQDNwkyvakTTZSbWo4enx_ZgRd2xVMlQV1Xb-vUjtRni1jRfONgwG5SfKaIvKtgH0FFtuKhbjlU2nDcw8m1JheO2ZyLt3Vtv0hizo49rXEr_Ck7dj-wibAQ6B&sig=AHIEtbRallEW86bs2qN3VdcAR2SK5Nno6w

I hope this was useful and please comment if this was helpful to you.

Apr 29, 2011 | Adtran Netvanta 3430 Router

1 Answer

I have Kyocera Mita KM-2050 Printer/Scanner. The machine has moved networks. I have setup the printing OK but cannot get the scanning to work. I have gone into the panel on the machine & changed the IP...


The NIC card will need to be reset back to the factory defaults if you do not have the user name and password.

If you contact me through www.gfbm.net I will assist you with resetting the scanner over the phone.


Once reset the scanner NIC you will need to re input the IP and all your other scanner information.

I hope this is helpful,
Shawn

Jan 31, 2011 | Kyocera Mita KM-2050 Printer

1 Answer

Is there a way to perform local password recovery on a Netvanta 3200 router?


can you not reset it, there should be a small hole at the back of the router
just push the point of a pen in the hole and that should reset it..

Nov 24, 2010 | Adtran NetVanta 3200 Router

1 Answer

(F5D6230-3) Wireless Router: i need to know how to change my mac address on my ...


In your browser's address bar, type 192.168.2.1.

By default, leave the password blank.

On the Belkin setup page, go to Internet WAN.Then go to MAC address. You may close your computer's MAC address or type a specific WAN MAC address, if required by your ISP.

I hope this helps!

May 16, 2010 | Belkin (F5D6230-3) Wireless Router

2 Answers

Reset ip , how


You can reset your router to factory defualts.
For that press RESET button for 10 seconds .
Reset button is in back panel of router.
Press it for 10 seconds.
Then connect router to computer with ethernet cable.
Then you can access it with following link.
http://192.168.1.1
or
http://192.168.0.1
type user as "admin" and password as "admin" or blank or "password"
thne you can see configuration of your router.
Then you can change ip addreses in WAN settings.
Let me know if you need more assistance.

Nov 07, 2009 | 3Com OfficeConnect Wireless 11g Cable/DSL...

1 Answer

I need to break password, to change IP address


First RESET your router to defaults.
for that press RESET button for 10 seconds RESET button is in back side of router.
Then connect your router to computer with ethernet cable.
Then you can access it with following link.
http://192.168.1.1
or
http://192.168.0.1
type user as "admin" and password as "admin" or blank or "password"
Then you can see configuration page of router.
Set WAN settings as your internet service provider settings.
Enable DHCP .
CLick on wireless and enable wi fi.
If you want secure router then enable WEP security then add new code it is your password key for connect wi fi.
Let me know if you need further assistance.
Thanks.

Nov 06, 2009 | Alvarion BreezeNET AP-10 PRO.11

2 Answers

Forgot password of Adtran NetVanta 1224R Switch


  1. Recovering passwords requires direct physical access to a unit. This procedure cannot be performed remotely over Telnet, SSH, or the Web GUI.
  2. Connect a straight through serial cable to the console port of the unit.
  3. Configure a VT100 session (i.e. HyperTerminal or ProComm) using the following settings: 9600 bps, 8 bits, no parity, 1 stop bit and no flow control.
  4. Reboot the unit by removing the power.
  5. As the unit boots, you will be given the opportunity to break into bootstrap mode by pressing the ESC key within 5 seconds.
  6. While in the monitor mode issue the following commands:
Bootstrap# bypass passwords
Bootstrap# boot

Notice that you are issuing the boot command not the reload command following the bypass passwords command. Once the unit has finished booting up, you can issue the enable command and you will not be required to enter the privileged (i.e. enable) password. Once you are in privileged mode, you can view the configured passwords by using the show run command. A new password can also be entered by going into global configuration mode by using config terminal command and issuing the enable password <word> command where <word> is the new password. Also remember to change any Telnet, SSH or Web GUI passwords if necessary.

Below is a sample output of these steps:

Router (1200990L1)
Executing bootstrap...
ram: 268435456 bytes of RAM detected.
Serial Number: LBADTNXXXXXXXXX
Bootstrap version: 11.03.00, checksum: 0F3C, Thu Feb 09 17:40:34 2006
vfs: NONVOL: 120 tracks, 128 sectors/track, 1024 bytes/sector.
eth0/1: initializing...
eth0/1: MAC address is 00:A0:C8:XX:XX:XX
bootstrap: Checking boot configuration...
bootstrap: Primary image is 'NONVOL:/NV5305A-12-01-07b-E.biz'.
bootstrap: User escaped to command line interface.
cli: starting command line interface...
cli: starting user interface

Press '?' for help.
bootstrap#bypass passwords
bootstrap#boot

Mar 20, 2009 | Adtran NetVanta 1224R 24-Port Ethernet...

Not finding what you are looking for?
Adtran NetVanta 3200 Router Logo

Related Topics:

1,503 people viewed this question

Ask a Question

Usually answered in minutes!

Top Adtran Computers & Internet Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

kakima

Level 3 Expert

102366 Answers

David Payne
David Payne

Level 3 Expert

14161 Answers

Are you an Adtran Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...