Question about Wacom Graphire 4 "Silver" 4x5 (WMM132369)

3 Answers

Pen working incorrectly

I have plugged my tablet to the back of the computer, installed the new drivers, and restarted the computer and the pen still seems to not work correctly. The sensor reacts before I put the pen down on the tablet. I used it at work on a windows xp machine and it was doing the same thing, then I took it home to my Mac OSX machine and same thing. What can I do?

Posted by on

  • 1 more comment 
  • hisci25 Jan 17, 2008

    Before I put the pen to the pad it starts to write, so I cant stop the ink unless I move the pen completely away from the writing pad.

  • snoozing122 Feb 06, 2009

    I have the same exact problem, I can't seem to find where to set the big pen button as the main click, or what ever he was saying.

  • avrame Mar 12, 2009

    It's as if the pen nub is constantly being pressed - the blue LED turns green and remains green as long as the pen is close to the tablet. The pen does not register a click when it is pressed on the tablet, only when it gets close to the tablet. It's very annoying - and I'm surprised because I haven't used the tablet all that much. It's completely unusable like this.

×

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Everyone thinks the pen is defective, so it must be another problem like sensitivity settings, which can be changed.  See Manual.

Posted on Mar 05, 2008

Ad

I have the exact same problem, and I can't find anything, until now, on the web about it. I think perhaps the pen is defective because the mouse works fine.

Posted on Feb 06, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Set the Pen Tablet Properties to a click for the large button on the pen. Now when you are in the program you are trying to use, make all your selections using the pen with the click. I had the same problem in Photoshop. I would try and do something with the pen and it would start drawing before I ever touched the pad. When I set down the pen near the menu side of the pad and select the tool I want to use, it works fine and only draws while clicking. Hope it helps.

Posted on Mar 28, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Driver problem or the pen tablet?


Hello, Reena -

So, are you wishing to find and purchase a replacement "pressure thingie" for your tablet? The "pressure thingie", the electronic "pen" for your tablet, is called a stylus.

The Genius G-Pen 560 is manufactured by KYE Systems America Corporation. Go to this KYE web page and look at question 5 and the answer to it:
http://us.geniusnet.com/supports/g-pen-560

This link brings up the list of replacement "pens" which you can purchase:
http://us.geniusnet.com/pens

Best wishes.

Feb 15, 2018 | Genius G-Pen 560 (31100026100)

2 Answers

I have a genius wizard pen 4 x 3, about 5 years old. Can it work with a new computer that has windows 7, 64 bit?


hi, i have the same tablet wizard pen 4x3, windows 7 64bit install the tablet but doesnt work. if you could find a solution please contact me, i'll do the same for you, got this page in my favs for repair stuff..
esmilodonte arroba gmail dot com
peace and be nice

Apr 18, 2010 | Genius WizardPen 4x3 (K941C001) Graphic...

2 Answers

My Bamboo Fun Tablet pen/stylus is not working. The tablet registers that the pen is there, the light turns orange, but the mouse will not move, for either the pen or eraser side. It will move for my...


That happened to me yesterday. What I did was I went to the wacom site here: http://www.wacom.com/downloads/drivers.php, selected my tablet make and operating system, and downloaded the driver update. I installed it and as soon as it was done my pen started working again. Hopefully this works for you too!

Mar 02, 2010 | Wacom Bamboo Fun 8.5" x 5.3" USB Tablet...

1 Answer

Wacom Tablet Installation: Where's the Setup Process?


What you should do now is to go to Control Panel->Add Remove programs. Select the entry for this tablet and delete it. after disconnecting the tablet reboot the PC. Then without connecting the tablet, install the drivers, Reboot. Connect the tablet and allow Windows to detect the tablet and load its drivers. Then only will work properly.

Nov 19, 2009 | Wacom Graphire3 Tablet 6x8 (C267252627)

1 Answer

Computer does not recognize the device


Plug your Tablet in first with Computer off, Turn on Computer and see if Vista recognizes the Tablet. Go by what is suggested on the screen. It may help to do a Hard Disc DeFrag. before attempting the above.

Sep 15, 2009 | Genius G-Pen 4500, 4x 5.5 4x 5.5 tablet...

1 Answer

Pen doesn't work


Hi,

It could be the drivers problem which does not support operating system. Please visit the vendor web site and get the drivers for 64 bit OS.

Aug 05, 2009 | Wacom (PTZ930AC) Graphic Tablet

1 Answer

Genius MousePen 6x8 pen drags as if I'm holding down mouse button


Listen up kiddos! I had this same problem and I was troubleshooting....apparently you have to make sure you uninstall the old drivers first and delete the directory entirely, before reinstalling the software.
So, UNPLUG THE TABLET! This is the part that screwed me up... then go to start > all programs > tablet > uninstall. Run the wizard, restart, go to my computer > local disk drive > program files and delete the Genius Tablet folder. Then, install the drivers again, reboot, THEN and ONLY THEN, should you plug your tablet back in.

Mar 20, 2009 | Genius MousePen 8x6 (MOUSEPEN8X6)

2 Answers

My Genius Gpen 4500 has shown no Pressure recognition on Photoshop, Painter and the wizard.


Hello. I'm not quite sure if this will be useful for you, but i'll tell you what happened to me. I bought the very same model but without the mouse, the G-pen450. When I just bought it, I just intalled the driver from the CD, and both the painter X and photoshop cs1 trials included. I had no problem when I was drawing in photosho cs1, but when I uninstalled it and and installed photoshop cs2, I was still able to draw with the pen, but it had no pressure sensibility, no matter how hard did I press the pen against the table or how many times i enabled or disabled the pressure settings in both photoshop and the tablet driver.

what i did was downloading the new driver (the 2.0 version) for the g-pen450 from the genius page, and simply installed it ... and it didn't work, worse; now even the pen suite didn't recongize the pressure control, so, what I did was to uninstall the WHOLE software included with the table along with the driver, and then I reinstalled the new version (2.0). After I installed it, the instaling program asked me to restart the computer, so I did it. Then, after the computer was done restarting, I connected the tablet to a USB port, and then the computer recognized it, actually it told me that it recognized the tablet, two HID compatible dispossitives, and a HID compatible mouse pen. It opened that window that appears everytime you connect new hardware to the computer, and it proceeded to "install" all the drivers needed for the dispossitives.

After the computer finished installing, it asked again to restart the PC, soooo I restarted it again, when it was done, I connected the tablet once again, and this time it displayed that "your new hardware is installed and ready to use" balloon on the bottom right corner of the screen. So I tried opening photoshop CS2 again and drawing with the tablet, and this time it did work perfectly.

I think it's matter of uninstalling the old driver, and the bundle software (annotate all, pen commander, pen mail, pen signer, etc. ) and then instaling the 2.0 version of the driver.

Jan 15, 2009 | Genius G-Pen 4500, 4x 5.5 4x 5.5 tablet...

1 Answer

Genius g-pen 450 driver problem


Try to change usb port and reinstall driver some port on your PC may not regcognize it.
After I solve it , everything work fine :D

Apr 15, 2008 | Genius EasyPen (K9418400)

Not finding what you are looking for?
Wacom Graphire 4 "Silver" 4x5 (WMM132369) Logo

464 people viewed this question

Ask a Question

Usually answered in minutes!

Top Wacom Computers & Internet Experts

jasbo
jasbo

Level 3 Expert

2237 Answers

William F. Bryant Jr

Level 1 Expert

49 Answers

Alun Cox

Level 3 Expert

2678 Answers

Are you a Wacom Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...