Question about Panasonic PT-52LCX66 Projection Television

1 Answer

Bluish green tint to television picture

Previously I have had a great picture, with great colour, on my 51" Panasonic plasma television. It is connected to a digital cable box. Recently, the picture colour has changed. It is now a green and bluish tint. I have tried using the television's menu function to adjust the "coulour" and "tint" settings, but this does not seem to bring it back to its previous quality. My daughter first observed the change in colour. When she turned on the television (and the cable box) she noticed that the "Guide" offered through the cable box was a different colour. She went into the menu functions of the cable box to adjust the colour for the "Guide" and changed the colour to "Sage". She says that this is when the colour for the tv picture changed as described above. Do you have any suggestions as to what might have happened, and how to get the colour to return to what is was before?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Panasonic Master
  • 12,962 Answers

Find out what board and circuit is responsible for the color and you have your answer.

Posted on Mar 12, 2017


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 3130 Answers

SOURCE: Convergence Problem?

The convergence IC most likly shorted, and burnt out the b+ feed resistor. There are two IC's inside this set to control the green red and blue convergence. They are most likly STK 392-###. The ### is another set of numbers that change depending on the model of the set. They each have three amps inside each one. You really should have both of the IC's replace with only original parts, as sub parts do not hold up and will not last as long as they should. Both IC's are soldered into place and if you decide to do this yourself, please be aware of the extemly high voltage inside of these puppys. there really are no user replaceable parts inside these sets unless you have solid state repair experience. Not only will yopu need the proper IC's, but you will have to find out what was burning. my best advice, Play it safe and call in a trained tech to assist you with this repair. The price should run someware between 300 to 450.00 to repair. Good Luck Please do not forget to rate this thread.

Posted on Dec 08, 2006

  • 192 Answers

SOURCE: Component Video inputs do not work

I started back in the day of tubes. A family would have one set and it would be a 19" black and white. There are different resolutions now. The components probably do work, but, they don't pass the 480i signal. The satelite converter's analog signal needs to be set to 480p and the DVD needs to be set to progressive if it does have that setting. If the DVD is not a progressive scan DVD, then, the only inputs that it will show on is the analog signal. Some of the dish converters have a switch on the face for changing the resolution. If yours doesn't then put it in an analog source and go to the menu and change it there. Then move it to the component input. Hope this helps.

Posted on Jun 24, 2007

  • 70 Answers

SOURCE: Watching digital tv using a Panasonic DMR-EZ47VEB


This is a common problem, the problem is caused by the fact your device is connected to the TV via a scart lead. The way it works is this: If you press the AV button on your TV remote your TV will turn over to the first scart channel. If you actively do something on the device connected via scart in this case the dvd player, (this includes things like playing a DVD or Video, or going into a menu), the device sends a signal down pin 8 of the scart lead and turns the TV over automatically to the AV channel, BUT as soon as you come out of the menu or stop the DVD/Video the signal stops and the TV will revert back to the channel it was on.
So you have 3 choices......maybe 4...
1. press the AV button on your TV remote directly.
2. Buy yourself and HDMI lead IF your TV supports it (note: you will have to select the HDMI channel on your TV remote because the auto thing is only on scart leads).
3. ONLY DO THIS IF YOU HAVE A SPARE LEAD look up a diagram of a scart lead on Google so you can find pin 8 and cut it out with a pair of wire cutters. YOU will have to still press the AV button on your TV remote to go to the channel though,
4. Connect your TV and DVD with an aerial lead and tune channel 6 on your TV into the DVD player. ps then disconnect the scart lead.
(Go for choice number one!)

Posted on Jan 03, 2008

  • 108 Answers

SOURCE: Sony Wega 50" DLP bluish tint

the issue is the optical block. replace the optical block

Posted on Jan 09, 2009

  • 1689 Answers

SOURCE: No picture or sound

Make sure that there is actualy power going to the AC power source where the TV is plugged in. You can re-set the TV by disconnecting the power for about 10 seconds and then connecting it back again. If the set still does not start it will require service.

If the set is dead it is most likely the main power supply board that failed. The service tech would replace the power supply and also investigate to find the cause of the failure. Sometimes another board could have a failure and cause the power supply to be damaged.

If the set will not start up, it will require shop service. You can call Panasonic tech support to find out the authorised service rep for your area. Check to see if the set is still under warranty. If not, it will be expensive to service.

Jerry G.

Posted on Jan 17, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Green tint in picture

Are the lines completely through the screen or just the upper or lower part of the screen? If through the whole picture, lines in the picture of a plasma can be caused by a defective Main Logic Control board or a bad plasma panel. The panel, if available would be very expensive (cheaper to buy a new TV). If the lines are just on the upper or lower part of the screen then it is the upper or lower scan drive board. Here is a list of the parts for your TV.

Nov 04, 2013 | Panasonic VIERA TH-42PX60U 42 in. Plasma...

1 Answer

The picture on my 3 year old panasonic plasma turned green the other day. I've tryed adjusting the tint but it has not solved the problem.

There is a diagnosis on this, do a search on "dyna109_94_8750.pdf" on the net. I hope this helps you correct the problem.

Nov 20, 2010 | Panasonic TH-50PX75U Plasma HDTV

1 Answer

I have a Panasonic Plasma, believe model TH-42PWD6 and a separate Denon tuner. For a while the colours have been splitting into mostly green and purple. If I flick between DVD and TV it eventually resets.

I had a similar problem with the blue tint going away. I solved it by replacing the terminal board with a new component board I picked up on eBay. You can also use the PC input with a D-sub connector using a component cable adapter.

Sep 14, 2010 | Panasonic TH-42PX500U 42 in. Plasma...

1 Answer

Blue Picture

blue crt is bad and sorry to say not avail new any more

Dec 04, 2009 | Sony KP-51HW40 51" Rear Projection...

1 Answer

Grainy and red tint on component video inputs from

Usually when you have a red tint when using the component input i'ts because the wires are switched on one end or one of the 3 video wires is bad. See if blue and green are switched.I see this all the time. Is your picture grainy on all input?

Nov 22, 2009 | Panasonic TH-42PX75U 42 in. Plasma...

1 Answer

Green tint

It sounds like the color wheel has gone bad and needs to be replaced. This is located behind the back panel... replacing a new colour wheel will solve ur problem

thank u
rate me

May 29, 2009 | Sanyo DP42746 42 in. Plasma Television

1 Answer

Too much red color in the picture


Aug 27, 2008 | Hitachi 51G500 51" Rear Projection...

1 Answer

Orange projection lamp on. Picture is a bluish green, no true white.

If you are in warranty contact Lg electronics since they own Zenith. I was having similar difficulties and they are sending me a replacement tv even though I am out of warranty by 3 years.

Jun 09, 2008 | Zenith D52WLCD 52" Rear Projection...

2 Answers

The green light on for 2 seconds and off again (Panasonic TH-42PWD5UY)!

* cd-vcd-dvd-ld player.
* colour tv, Lcd/plasma tv.
* projection tv.
* prologic AMPS
* Grill/microwave oven's
* Digital proffesional camera.
* Digital camcorders.
* LCD/Digital projector.
* Hi-Fi music system.
* FAX machine.
* printer/scanner/copier.
* play station (PS1-PS2).
* X-BOX360.
DIAL..........: 9820380682

Jan 23, 2008 | Panasonic TH-42PWD5UY 42 in. Television

Not finding what you are looking for?
Panasonic PT-52LCX66 Projection Television Logo

Related Topics:

259 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Televison & Video Experts


Level 3 Expert

5318 Answers


Level 3 Expert

508 Answers

The Knight
The Knight

Level 3 Expert

74999 Answers

Are you a Panasonic Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides