Question about Whirlpool SF367 Gas Kitchen Range

Open Question

How to change the temperature sensor on a Whirlpool Accubake Model # RB5305PDQ6

Oven will not preheat after self cleaning. Trying to check the temperature sensor. How to change the temp. sensor??

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: whirlpool accubake oven will not heat after self clean cycle

I had the exact same thing...thermostat..

Posted on Jul 11, 2009

Ad
heatman101
  • 43501 Answers

SOURCE: I can't find my owner's manual - how do I clean my

Hi,
Before you go working too hard to get you oven to go into the self clean mode....check out this tip...


http://www.fixya.com/support/r3969401-self_cleaning_oven_problem

heatman101

" Wish I had read this first. I never would have used the self cleaning option. Thanks for the info!! " - amymrocks

Posted on Apr 20, 2010

marka19
  • 1430 Answers

SOURCE: whirlpool accubake self cleaning super capacity

This sounds like the relay on the main board has failed. You will need to see if you have power going into the control. If you do replace the ERC (main control). You can also carefully inspect the board for burn marks if you see any replace it. Here is a link that will help you check and replace this http://appliancehelponline.com/ovenerc.html

Posted on Sep 13, 2010

ginko
  • 19396 Answers

SOURCE: I have Whirlpool Schott Ceran

Hi.

F3 E2 is a temperature runaway error. It means that the control board detected that the oven is too hot. If there is no effective overheating the error occurs because the temperature sensor is shorted.

here the explanation from manual:

F3 E2 : Oven too hot, over heating

Solution:
Test and replace oven temperature sensor.

Before replacement the temperature sensor must be tested. A good sensor will read about 1080 Ohms at room temperature. If the sensor is shorted will only read a couple of Ohms or zero.

If the sensor is good the problem can be the control board, wiring to temperature sensor, or in sporadic cases an heating element that stays always on because of a wiring contact. The last case is quite uncommon.

The most common fault is a defective temperature sensor. The sensor is a probe located inside the oven cavity. The sensor is attached to a two wires connector and held by one or two screws. Disconnect power. Remove the sensor. Undo connector and read Ohms at connector. If there is low impedance replace the probe.

Here a tip explaining how to find parts and diagrams for most aplliances: Where do I find parts and diagrams for my appliance?

Regards.

Ginko

Posted on Sep 07, 2011

  • 77 Answers

SOURCE: oven is 75 degrees off temperature setting. what do I do?

Are you sure that no one has been taking the control nob off of the dial and turning it as a prank?

Posted on Feb 08, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oven is 75 degrees off temperature setting. what do I do?


Are you sure that no one has been taking the control nob off of the dial and turning it as a prank?

Feb 08, 2012 | Whirlpool Accubake RF362LXTS Electric...

1 Answer

I have a Whirlpool Self Clean oven Model number:RBS305PDS17. I used the self clean feature and now my oven will not heat up. All the digital controls work such as preheat and temperature, however there is...


Error code E2F3 indicates oven overheating, i.e. sensor is not cutting off heat. Replace the sensor, about $75 online. If you have done this more than twice, or if oven is acting strangely (for instance, broiler comes on during "bake" preheat), replace control board OEM part #8302994, about $170.

Aug 16, 2010 | Whirlpool Ovens

1 Answer

Started the clean cycle but remembered that I wanted to remove the oven racks and quickly tried to turn off the oven but the door had already locked - now I can't get it to unlock - what happened? This is...


It can take 4 hours to complete. I also see that many people have problems with the temperature sensor "Blowing" after they use that function. When you do the clean special door interlocks activate and the oven heats up to like 900 degrees!

Feb 18, 2010 | Whirlpool 30" Self-Cleaning Freestanding...

1 Answer

My oven flame is yellow and orange. you can smell


open air vent on main burner. check burner orifice and pressure regulater

Dec 31, 2009 | Whirlpool Accubake SF362LXTS Kitchen Range

1 Answer

Oven clicks to self cleans or f3, the door locks and food burns


Replace the oven temperature sensor.
Take your model number to any appliance parts store for a replacement sensor.

Apr 20, 2009 | Whirlpool Accubake RF362LXTS Electric...

1 Answer

Whirlpool accubake doesn't preheat properly


Are both of your heating elements lighting up when you are preheating? It sounds like the oven thinks it is pumping power into both elements and one isn't working. Oven elements are generally easy to remove and replace!

Jan 08, 2018 | Whirlpool Kitchen Ranges

1 Answer

Whirlpool Accubake - Can't get out of clean mode


cannot get out of clean mode, although the oven outside is cool, but door is locked and display still says cleaning, door locked and time of 3 hrs 15 min is displayed. NOW WHAT?

Nov 16, 2008 | Kitchen Ranges

1 Answer

Oven wont work after self clean


I have a Whirlpool MOD. RBS275PDB17 single electric self-cleaning oven; although the manual is generic, it specifies, "When the cycle is completed and the oven cools, "End" will appear on the lower oven display and "LOCKED' will disappear" and "To Stop Self-Clean any time: Press UPPER/OFF, LOWER/OFF or OFF/CANCEL. If the oven temperature is too high, the door will remain locked. It will not unlock until the oven cools." Has your oven had time to cool?

Jun 13, 2008 | Whirlpool RBS275PD Electric Single Oven

Not finding what you are looking for?
Whirlpool SF367 Gas Kitchen Range Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Kitchen Ranges Experts

Ismael Rodriguez...

Level 2 Expert

184 Answers

Cindy Wells

Level 3 Expert

6004 Answers

Archie Ferrarini
Archie Ferrarini

Level 3 Expert

869 Answers

Are you a Whirlpool Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...