Question about Philips 43PP9202 43" Rear Projection Television

1 Answer

Intermittently screen move to one side with distrited picture


Intermittently picture start moving towards left and stay at half a feet gap.

Engineer who attended mentioned that it is the common problem in this model and he fixed a colling fan above two power transistor to keep it cool. Some times the porblem doesnt appear for months and some times it keeps comming every day for week.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 111 Answers

Might be the convergence chips. Do you have any problem moving the convergence under the menu setting? Convergence chips are reasonably priced. If you know a friend or someone who can solder better than average, I would go this route. My tv wasn't that bad; I wasn't able to set 2 of the 3 colors during convergence setup. Changing the 2 convergence chips did the trick!

Posted on May 24, 2009

  • cp12912 Mar 31, 2010

    Agree. Convergence chips. Here's a tip: don't let your kids plug their gaming consoles into your projection tv. It overloads the convergence chips and then you'll be in the same boat again.


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to lubricate a precor treadmill belt?

About This Video

Video about How to Lubricate a Treadmill using Liquid Lube
  • This vidoe will demonstrate how to properly lubricate your treadmill belt and deck. This demonstration is for the application of liquid lube.
  • To begin, clean the deck and belt by loosening the rear roller bolts 10 turns as seen in the video. It is best to loosen each side five turns and then repeat the process.
  • Now that the belt is loose you can take an old towel and place it under the belt as shown in the video. Move the towel up and down the deck, then using your hands pull the belt around half way to ensure you have completely cleaned the back of the belt. Then remove the towel.
  • Open your lube packet and use half of the package to make a half circle on the deck, from the front outer portion of the deck toward the center and then back to the outer edge. Use about half the package for this arc. Now repeat the process on the opposite side. Be sure to wipe up any excess oil as it is very slick!
  • Use your hand to move the belt around some more to begin spreading the lubricant out.
  • Now tighten the rear roller bolts back to the exact amount of turns they were loosened previously.
  • Power on and start the machine and let it run slowly for a few seconds to make sure the belt is staying aligned in the center of the deck area. If it is not centered correctly, make minor adjustments to correct the issue. Tighten the left bolt to move the belt to the right and tighten the right bolt to move the belt to the left. Now walk on the belt for a minute or so to fully distribute the lubricant.
  • This concludes todays demonstration of how to lubricate a treadmill using the liquid lube.

How to Lubricate Treadmill Using Liquid Lube Video

Apr 30, 2014 | Precor 9.21 Treadmill

1 Answer

Vertical blue transparent line plasma

Check for loose or dusty flexible connectors. (Please take care to switch off TV and remove plug from the power outlet and discharge high voltage capacitors before you do anything on the PCB) Apply cleaning oil in connectors wherever possible and remove and reconnect it a few times. If problem persists, it might need attention by a qualified service technician.

Jul 22, 2012 | Nakamichi VU50P 50 in. HD-Ready Plasma...

1 Answer 300+II when given for printing head and paper moves however it doesnot print

it might be because the gap between the paper roller and the print head has increased. There is a lever on the left hand side of your printer and some markings are there 0, 1, 2, 3, move the lever towards the figure 0 or push it towards the paper roller.
To fin d the lever remove the top black cover, you will find a rod on which the print head moves, look towards the left of the rod and there you will find the lever.
This might help you, for further solution you can find me on fixya.

Apr 17, 2011 | Epson LX-300+ II Matrix Printer

1 Answer

There is a black gap between the actual picture and the right edge of the monitor and it also "pushes" the picture into the left edge a half an inch or so, rendering it unviewable on the left...

the "horizontal position "control has been tampered with .but locating it and setting it can be hazardous so only a qualified person should do it .

Mar 06, 2011 | Samsung DynaFlat TX-R2035 TV

1 Answer

The mouse pointer on my HP nc6320 jumps around intermittently and is very difficult to control. This problem only occurs when the laptop is fully charged and is running off the battery. If the battery is...

Hi Alan,

From your description I understand that the cursor jumps intermittently. This happens when the sensitivity of the touchpad is more or high. Try lowering the touchpad sensitivity.

Here are the steps:

1. Click Start.
2. Click Control Panel.
3. Double-click Mouse.
4. Click Device Settings tab in the Mouse Properties window.
5. Click Settings Button to launch Touchpad settings.
6. Go to Configuring Sensitivity on the left side menu.
7. Move the slider towards left to decrease the sensitivity.
8. Also, click on PalmCheck on the left side and move the slider towards maximum.
9. Click Apply. Click ok
You can try reinstalling the touchpad driver from the below links:

Windows Vista:

Windows XP:

Dec 30, 2009 | HP Compaq nc6320 Notebook

1 Answer

I have the Sony KV-36XBR400. The picture freezes intermittently. Sound is OK. When I turn TV off and on again, I may get a good picture for about 15mins, sometimes longer. Sometimes half of the screen will...

Hi.. Sorry to hear that the Picture is freezing.. Here are some of the steps that you can try:
*Try to connect a different video source with the TV like DVD Player, Blu-ray player and check.
*If the issue persists, disconnect the power cord and reconnect to a different wall outlet without the Power surge protector.
* If the issue persists, you need to contact the nearest service center to fix this.
Yes, you were correct many LCD TVs have problems compared to this TV.

Sep 22, 2009 | Sony FD Trinitron WEGA KV-36XBR800 36" TV

1 Answer

Half a screen

The solder joints have cracked on the vertical output IC. If you have soldering experience you can resolder them yourself but if not then let a qualified tech handle it for you.

Jul 06, 2007 | JVC AV-27530 27" TV

2 Answers


jesus have you move that tv thats new to me but surely techman know about.....good luck

Aug 08, 2006 | Optoma RD50 50" Rear Projection HDTV-Ready...

Not finding what you are looking for?
Philips 43PP9202 43" Rear Projection Television Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Philips Televison & Video Experts

The Knight
The Knight

Level 3 Expert

74106 Answers

matt martin
matt martin

Level 3 Expert

1210 Answers

Jaime Hernandez

Level 3 Expert

2318 Answers

Are you a Philips Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides