Question about Kirby G4 Bagged Upright Vacuum

1 Answer

Kirby G4A I have just had the motor rewound it has taken 4 weeks to get it back .What I need is a work shop manual so I can put it back together. Help

Posted by on

  • phil c Oct 21, 2007

    I would like to thank Marci for the solution it is the link below.

    http://reviews.ebay.com/REPLACING-THE-PO...

  • mk2020 Apr 14, 2008

    took it apart, it needed a power swicth, got used power swicth cant rember how it goes back .

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 357 Answers

YOU'RE WELCOME!! :0)

Posted on Oct 23, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

New power cord required for g4a kirby


Are you looking where to buy one? Any vac shop website should have one, Amazon, or Ebay.

Feb 15, 2014 | Kirby G4 Bagged Upright Vacuum

1 Answer

I need to put the neutral pedal back together


will need to get Kirby engineer to repair, should cost 39 callout+28 for new pedal

Jan 11, 2013 | Kirby G6 Bagged Upright Vacuum

1 Answer

Can't find owner's manual. need to use my kirby g4 to inflate an air mattress. help


Remove power head and bag from motor install pig nose attachment on front where powerhead goes install hose on back where bag attaches put inflator tool on hose

Jul 06, 2009 | Kirby Vacuums

2 Answers

It's been awhile since I have used my shampoo system on my Ultimate G series Kirby. Well, as instructed I took it apart and cleaned it. Now I can?t figure out where to put the ?screen cap? and ?sponge...


Hello,
The littlew round screen goes in the hole where the hose attaches to the tank. The round foam filter goes up in the hole underneath the on/off valve for the foam. Here is a guide if you need any more help...

http://reviews.ebay.com/KIRBY-CARPET-SHAMPOOER-INSTRUCTIONS-MANUAL-DIRECTIONS_W0QQugidZ10000000004594992

Marci

Jun 15, 2009 | Kirby G6 Bagged Upright Vacuum

1 Answer

I have the bag unhooked and the hose connected to the motor which has engaged the safety switch but the Kirby will not turn on to blow air


Blower instructions HERE. It MUST help.
If you put it back together as VACUUM and it works with hose (attached to suction) and the nozzle - no problems with Kirby. Then you must not be turning the hose on the exhaust all the way. Sometimes it is pretty hard...Or maybe the safety sup plastic that presses the safety switch on the front of the unit is broken.

Good Luck,
Rocky

Jun 06, 2009 | Kirby Ultimate G Bagged Upright Vacuum

1 Answer

TechDrive power assist fell off


See if THIS helps.
Not sure how far you went disassembling the unit so here are a few more useful articles that you may want to see:
How to connect wires
How to get the transmission installed.

Rocky

May 30, 2009 | Kirby G5 Bagged Upright Vacuum

1 Answer

Dont know how to put the shampoo system together on my kirby g6..


http://reviews.ebay.com/KIRBY-CARPET-SHAMPOOER-INSTRUCTIONS-MANUAL-DIRECTIONS_W0QQugidZ10000000004594992

Copy and paste the above link to the address window of your browser for the Kirby Shampooer instructions.

Hope this helps :)

And thank you for using Fixya!!!

May 02, 2009 | Kirby G6 Bagged Upright Vacuum

1 Answer

New roller brush for g4a


Usually between $24-$30 depending on where you look.Shop around a little.Any vac shop should have them.

Nov 02, 2008 | Kirby Vacuums

1 Answer

Kirby 5 Model G5D


is there a re set button on a Kirby. Used the vacuum 2 weeks ago, worked just fine. Went to use it today and it won't start. Any ideas?

Jul 31, 2008 | Vacuums

1 Answer

User manual required


if you are in the US you need to call 800-437-7170 to get a manual - i'm not sure it will help in enough internal detail to help you get things back together, but the same number is for Kirby technical support and they may talk you through it. If you want to try online then; http://www.kirby.com/CustomerService/ContactUs/tabid/73/Default.aspx if they don't, then please take a good selection of photos of what you have, and post them back here or try and call on a live chat and we can see what we can do to help. Hope this helps you out :)

Apr 21, 2007 | Kirby G5 Bagged Upright Vacuum

Not finding what you are looking for?
Kirby G4 Bagged Upright Vacuum Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kirby Vacuums Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18424 Answers

Jim Parker
Jim Parker

Level 3 Expert

1041 Answers

Richard Agent

Level 2 Expert

98 Answers

Are you a Kirby Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...