Question about Technics SL-1200M3D Turntable

1 Answer

On/Off Switch NonOp Repair?? or Replace?? Best place to Buy switch??

On Off switch non-op, where do I get a replacement

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

You can get a replacement here:

Posted on May 23, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Headlight switch will not work. Is there a repair or should I replace switch. Best place to buy new switch?

There's 2 general types of switch. A stalk/indicator switch and a dashboard style switch.

You'll get both from your main dealer or can order from most car spares shops.

If it's the second type of switch pictured above, check how many terminals are on the rear of the old one before you order a new one.

It's probably better if you search Ebay for 'headlight switch' or 'Jeep headlight switch' ... whatever make of vehicle you have
headlight switch

Nov 07, 2015 | Cars & Trucks

1 Answer

Is there a way to get seiko to repair my 7N43-8A38 "A1" Watch?

If it has a battery op movement you could have a non original batt op movt installed for 15 bucks and it will work like new but if it is a mechanical movement then you will have to replace necessary damaged parts

Feb 01, 2015 | Seiko Watches

1 Answer

Heater won't operate

If the switch is easy to access, you could simply replace it -- but finding the switch may be nearly impossible, because of the type of unit you are talking about. Also, some of these oil gel heaters have the electronics encased in a non-acessable area, meaning if one component goes bad, the unit is basically done. Your best bet to find the switch is to start with the manufactures website. if there are no diagrams or repair manuals, you should be able to find some contact information about repairs

Oct 01, 2012 | Lakewood Oil-Filled Electric Radiator...

1 Answer

Maytag washer (M#FAV6800AWW) displaying error code OP. We already replaced the clutch, the shocks, and the unbalance sensor. TY


OP means that the lid does not close. Usually you need to replace the lid lock. Here the part.

The lid switch and wiring should be tested before replacing the switch. Pages 31 and 32 in this service manual show how to test the switch.Make sure power is disconnected before carrying maintenance.

Here all parts and diagrams for your washer.



Dec 07, 2011 | Washing Machines

1 Answer

2 burners on elctric stovetop/oven non/op. replaced. still non/op.

Have you checked the switches to see if they are providing power to the burners?

Feb 11, 2011 | Whirlpool Kitchen Appliances - Others

1 Answer

2002 BMW 325ci Power window, driver side button collapsed, nonop

unfortunately there is no way to "fix" that particular issue. the switch needs to be replaced.

Nov 08, 2009 | 1999 BMW 318 ti

1 Answer

High speed only working 2nd and slow speed non functioning

Most likely the fan speed pull chain switch. It can be found at home depot for about $5. Buy the new switch before you remove the old switch. Then remove and replace one wire at a time, they will be labeled L-1-2-3

Aug 23, 2009 | Dryers

2 Answers

Have the OP signal, have cleaned all latches and lid areas but still not working. how do i pop off the top portion to check the side locking latches? i can see they are not well sealed and would rather fix...

This is a common problem on this washer. (The OP fault code). It is caused by a faulty magnetic reed switch. Apparently, the lid on these washers isn't completely watertight and allows water/moisture to get into the switch and corrode the wires and connections.

The switch is on the left side under the rubber bumper, Release two spring clips in the front between main top and front panel using a putty knife. Lift the top. To access and see if the magnet is in place, remove the dispenser from lid. Gently pry the bottom of the plastic inner lid toward you and down. This will let you see if the magnet is in place on the right front corner of the inner lid. Here is a picture of a bad door lock switch:

Sure hope this helped and best wishes.

Jul 27, 2009 | Maytag Neptune FAV6800AW Top Load Washer

3 Answers

My 1995 chevy 6.5 L diesel dies at highway speeds. Why?

I could bet 99.9% with out seeing the truck my self that your probelem is the PMD I have two of these trucks and know many people that also have them and the vast majority of problems with the Chevy 6.5L diesels are from the PMD. A must when replacing the PMD is moving it from its place on the injection pump on the top of the engine to a place that dosent get so hot. A good place is the front bumper or skidplace, search for Heath Diesel they have a kit to move it. Its worth every penny.


Jan 26, 2009 | 1995 Chevrolet K2500

1 Answer


the door inside panel is screwed on in 3 or 4 places. look on the underside of the panel for a screw or two, and look for a screw cover underneath where the inner door handle is. pop the window switch assembly out of the door gently and unplug the wiring harness from it. it is possible to repair the window winder assembly inside the door, but its too hard a process for me to explain. if u can get the door panel off, but cant figgure out how to repair the winder assembly, then buy a new window winder assembly for around $120, to replace and not repair is the standard practice anyway, cause the winders are a pain to repair, and the repair is usually only temporary, they are technically non repairable, the repair is more like a mcguyver move.

Nov 23, 2008 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
Technics SL-1200M3D Turntable Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Technics Audio Players & Recorders Experts


Level 3 Expert

5391 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Ben Armstrong

Level 2 Expert

357 Answers

Are you a Technics Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides