Question about JVC HR-J461MS VHS VCR

1 Answer

Tape stuck in VCR

Went to remove the tape and it will not come out.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 4,889 Answers
Re: Tape stuck in VCR

First locate the load and unload motor, it is the one with the rubber drive band. release the drive band and rotate the gear to raise and pull the carriage back into position.
This should remove your cassette, and put the carriage back into position.

Posted on Oct 19, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

How to eject stuck tape

might have to remove bottom of vcr and manually move the drive motor by the belt or the pully. if the bottom doesn't come off, you'll have to remove the top. usually screws on the side bottoms and one in the back. you can reach the motor from there.

Feb 27, 2014 | Mitsubishi VCRs

1 Answer

Tape stuck in vcr. when you press the eject button vcr starts to work but shtuts off the power Model number DVR-3034N. I have only taken the front and back covers off. Turned slanted roller untill the...

It sounds like the tape is jammed in the vcr, remove the top cover of the machine this will expose the tape. If the tape is spewed in the mechanical section and around the video head, get a pair of scissors and start cutting the tape and carefully remove all tape particles, when all tape debris has been removed, plug in vcr turn on and eject. If the tape looks good, you may have a loading basket problem, bad idler ***. or broken drive belt. "Lets hope for the best"

Jan 25, 2011 | Emerson VCRs

1 Answer

VCR tape won't eject


The reason your tape wont eject is either because, it is stuck or the tape run loose inside of it.

To remove the tape, unplug the VCR, then unscrew it open, you will have direct access to the tape, so try to plug it back and press eject, when it gets stuck, apply a little force in pushing the tape up, to the height where it is to pass out, and it will eject your tape.

If you are not familiar with such activities, i will advice you get a repairman to get this done for you, in order for you not to damage any other part inside the VCR.

Take cacre and good luck

Oct 14, 2010 | Sylvania LV448HG VCR

1 Answer

Had a stuck tape its gone now but still having trouble.

The tape is stuck in the vcr and doesn't get released. How can I remove it?

Aug 15, 2009 | Emerson EWV601 S-VHS VCR

1 Answer

GE vcr tape stuck

when this happens to me, i disconnect the vcr and remove the screws to the top cover. i remove the cover and carefully remove the tape, being careful not to touch any of the parts of the vcr. but please make sure the vcr is un plugged.

Dec 08, 2008 | GE VG4052 VCR

1 Answer

Error 2 on Front Panel

I'm not sure if this is a solution, but it cleared up the problem for me. It turned out there was a loose paper label for the cassette that got stuck inside the VCR with the cassette.

I had to take off the top of the VCR by removing the three screws. I then removed the jammed loose paper and then was able to get the cassette out. The flashing number 2 (whatever that means) went away. The machine seems to be working fine now.

Apr 19, 2008 | Philips VR620CAT VCR

3 Answers

Video tape stuck

Unplug the VCR, take the cover off, find the motor (probably on the right side of the mechanism) and turn its shaft with your fingers until you have run the tape back out. Now plug it back in and try it again with a scarificial tape. If it continues to fail, replace all the rubber belts in the mechanism.
Hope ya fix it!

Jan 05, 2008 | Panasonic AG-1330 VHS VCR

1 Answer

Error message E4 and stuck tape

Yes with care. Simply remove the cover and with care unwrap the tape. If you must break the tape - but make sure all residual tape is cleanly removed. Re assemble and put a tape head cleaner through- following the instructions.

Jun 22, 2007 | Mitsubishi HS-U445 VHS VCR

1 Answer

VCR tape stuck

Yes, it is a mechanical problem. While the tape is in fast forward the gears are engaged and locked to provide drive to the spindel on the right, however when you press the rewind button without hitting stop, the gears try to engage the spindel on the left without stoping and reversing (changing rotational positioning), this causes the motor to stop (this emulates a tape jam)the tope is left in and the unload mechanism never spools the tape back in because the motor has stopped. To free the tape, what I do is open up the unit and find the main motor check to see if the belt has slipped, if it has not try to manually spin the motor to engage the unload mechanism and eject the tape.

Dec 18, 2006 | Zenith VCS442 VHS VCR

Not finding what you are looking for?

Related Topics:

144 people viewed this question

Ask a Question

Usually answered in minutes!

Top JVC VCRs Experts


Level 3 Expert

4518 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

alexander woolfolk
alexander woolfolk

Level 2 Expert

276 Answers

Are you a JVC VCR Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides