Question about Cobra 148 GTL 120-Channels Base CB Radio

1 Answer

148 mic wiring white d104 - Cobra 148 GTL 120-Channels Base CB Radio

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

  • Expert
  • 113 Answers

Five pin /4 pin? (white D-104?)
five pin= 1-audio,2-shield,3-RX,4-comm,5-TX
4 pin=1-shield-comm,2-audio,3-TX,4-RX

Posted on Feb 14, 2015

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
Mechanic688
  • 204 Answers

SOURCE: mic wiring

Hello, In case you haven't found it yet, here is for a 2510/ which is a cousin of a radio.

1 - Modulation/ Audio/ White
2 - Ground/ Shield
3 - Transmit/ Red
4 - up button/ NC
5 - down button/ NC

Thats if the D104 is a 4 wire, Mechanic

Posted on Nov 05, 2008

  • 773 Answers

SOURCE: 148 gtl 5pin

Looking from inside the radio at the mic jack, with the nub down. Starting from the left is pin 1, pin 2, pin 3, pin 4, and pin 5.

here is the colors that should be attached to each.

1 is white.
2 is sheild.
3 is black.
4 is red.
5 is blue.

Hope this helps. Take care in soldering. It is easier to reach the pins if you remove the 4 screws that hold the face plate on. Be careful not to pull another wire from somewhere.

Posted on May 03, 2009

SD Tech
  • 14553 Answers

SOURCE: I have a astatic d104

If you bought the mic new it came with a sheet telling what wires do what, most of those are six wire mics.

In your radio: 1=shield, 2=audio,3=transmit, 4=receive.

On most astatic mics shield is braided shield wire, audio is white, transmit is red and blue is receive.

The other two wires should be yellow and black, the yellow will not be needed and you may have to connect the black to either pin one or pin 4.

Best way to do this is wire the shield and receive first and connect mic, if you have receive, then go for the audio and transmit.

There are a couple of versions of this radio so you may have to experiment to get it right, Keep the solder connections neat and the wire short.

Let me know with a comment here if you have questions.

SD TECH

Posted on Dec 11, 2010

  • 1212 Answers

SOURCE: I have a 1990 cobra 148 GTL with 5 pin

The wiring is not likely to be the same.

The information on the radio is here:
http://www.cbtricks.com/radios/cobra/148gtl/index.htm

You will likely need to open up the mic to identify what your wires connect to to determine the correct oreintation. it is possible too you may find one of the models listed was used by Barjan and is nothing more than a rebranded microphone.

Posted on Feb 19, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Microphone wiring


the rf power going out is geting inducted on the wires of the mic.try using some ferrites close to the coax on the pl259 connector and on the mic wire itself.

Mar 01, 2014 | Radio Communications

1 Answer

When i keyup my d104 mic on cober 148 gtl ihear feedback squeal.but the d104 work good cobera 2000 gtl


try to keep the mic away from the radio speaker.check to see if its turned up to high.check your mic gain to make sure its like 1/2 open.If these fail then you could solder two 0.001 ceramic disc capacitors from the audio to the shield wires about 3" apart.then on the audio wire in between the 2 caps solder a 4700 ohm 1/4 w resistor.this should work.

Nov 09, 2013 | Midland 1001Z 40-Channels Base CB Radio

1 Answer

I have a emperor ts-5010 that i would like to put a d104 hand held on but cant find any mic wiring for this sort of thing


  • Hi, I can help.

  • Your gonna wire it up the same as you would a D104 as follows ---

  • 1 - White - Audio
  • 2 - Shield and Blue (Ground and Common)
  • 3 - Red -Transmit
  • 4 - N/C
  • 5 - N/C
  • Yellow - N/C
  • Black - N/C

  • Please note that any wire marked "N/C" are not used for this setup.

  • If you have any comment please feel free to leave them here.
  • Hope this helps and thank you for using FixYa.

Regards, Tony

Sep 15, 2011 | Radio Communications

1 Answer

I have a hand held D104-M6 and I can't find the


I'm not sure if this will help but I'll try

Pin 1-Blue and Sheild

Pin 2- White

Pin 3- Red

Pin 4- Black
Hope this helped,all Astatic mics are wired the same.

Jun 22, 2011 | Astatic Radio Communications

2 Answers

I have a uniden Grant like to wire up a 4 wire D104 the mic has white black red shield


Wiring 1 4 pin D104 mic to a Uniden Grant CB is as follows -
  • Pin 1 - Shield - Shield
  • Pin 2 - Audio - White
  • Pin 3 - Transmit - Red
  • Pin 4 - Receive - Black

Regards, Tony

May 05, 2011 | Uniden GRANTLT 40-Channels Base CB Radio

1 Answer

Im trying to wire a astatic d104 m6b to a galaxy 949 mobile can you give a color code for what color wire goes were?i have black white red blue and a bare wire thank you.


This works for any mic.
dont worry about color codes. look at the switches.. there will be a common on both poles of the d104.. those need to be tied together to grnd. pin 1 on mic . the others d104 on n/c side is your rx. pin 4... the n/o one will be your tx pin 3 the other n/o will be audio and will have a wire from the mic element also on that pole of the switch. pin 2..

Sep 25, 2010 | Galaxy Radios DX-949 40-Channels Base CB...

2 Answers

How do i wire my d104 m6b mic for my president dwight d cb raido


Hi,

This must be the right pinning

Pin 1 = shield / blue
Pin 2 = white
Pin 3 = red
Pin 4 = black

good luck,
Gerard

Feb 05, 2010 | Astatic 636L Noise Canceling Microphone...

1 Answer

How do i wire a d104 desk mic to a madison base radio


You don't mention if the Madison is a 4 pin or 5 pin also you don't mention if the D104 is a 4 wire or a 6 wire microphone so this will be rather lengthly of an answer so if I help you could you atleast do the rating for me ? So here goes 4 pin / 4 wire 1]SHIELD 2] WHITE 3] RED 4] BLACK....O.K. 4 pin 6 wire 1]SHIELD & BLUE 2] WHITE 3] RED 4] BLACK YELLOW NO CONNECTION.....Are you with me so far ? Half over 5 pin 4 wire 1] WHITE 2]SHIELD 3] BLACK 4]N/C 5] RED.....5 pin 6 wire 1] WHITE 2] SHIELD&BLUE 3] BLACK 4]N/C 5] RED.I hope this helps you GOOD LUCK and have a good day Dan.

Jul 12, 2009 | Magnum DeltaForce CB Radio

1 Answer

Wiring a mic


Pin 1 is white
Shield and blue is to Shell. Guess it means ground
Pin 2 is Red
Yellow and Black no connections. Hope this helps................

Mar 25, 2009 | Magnum DeltaForce CB Radio

1 Answer

Mic wiring


Hello, In case you haven't found it yet, here is for a 2510/ which is a cousin of a radio.

1 - Modulation/ Audio/ White
2 - Ground/ Shield
3 - Transmit/ Red
4 - up button/ NC
5 - down button/ NC

Thats if the D104 is a 4 wire, Mechanic

Aug 30, 2008 | Cobra 18 WX ST 40-Channels Base CB Radio

Not finding what you are looking for?
Cobra 148 GTL 120-Channels Base CB Radio Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cobra Radio Communications Experts

AnyMHz.com
AnyMHz.com

Level 2 Expert

500 Answers

Steve

Level 3 Expert

3287 Answers

Brad Brown

Level 3 Expert

15628 Answers

Are you a Cobra Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...