Question about Baby Lock Sewing Machines

1 Answer

Tune up instructions - Baby Lock Sewing Machines

Posted by Anonymous on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 2 Answers

How to tune up a 2002 S10

Posted on May 10, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Bobbin housing new home deluxe 445

here is a link for a manual, it should have the information about the bobbin housing in it.

New Home 445 Instruction Manual

Dec 10, 2014 | New Home Sewing Machines

1 Answer

Inhereted a New Home model 920 without instructions. Motor sounds like it wants to work but is very slow and barely moves-unable to use, Please advise.

Take it in for service. Too many folks buy machines and do not use them. This is worse than anything you can do to them is NOT use them. With long periods of non-use, always plug in and run motor forward and backward for 10 minutes at least.
This one sounds like it's in need of service and a good lubrication and tune up.

Feb 03, 2014 | New Home Sewing Machines

1 Answer

High pitched noise while stitching

Stop using the machine, it Needs to be tuned up and adjusted. Have it tuned up by a experienced repair technician.

Jan 28, 2014 | Sewing Machines

1 Answer

Looking to tune up brother CP 6500. Squeaking And skipping occasional stitches. What grease to use and where to apply grease?

No grease please, only quality sewing machine oil. Some machines marked the oil positions with red. Small holes. Else take the top and left side covers of and use just a drop of oil where moving parts are joint. Here too you should find small holes that need a drop now and then.

Jan 11, 2014 | Brother CP6500 Sewing Machine

1 Answer

Wont sew bottom looper not working

Check threading and put in new needles, if it doesn't work after that. Make sure to thread it per instructions and in the right order. If you don't it won't work properly.
If that fails a tune up will be needed.

Aug 20, 2011 | Singer 14SH654

1 Answer

Bernina 1010 (approximately 20 years old): the bobbin winder has stopped rotating- only a turn or so and then stops

Hello, from one sewer to another, a machine that is 20 years old does need a professional tune up from time to time. If you can, take it to a sewing machine store or a sew/vac store to get a professional cleaning and tuning. There are manuals on how to do this, but it is best to leave it to a pro. I own a number of vintage machines and I can tell you, I have wasted countless hours trying to do it myself until I found a pro in my area who sell vacuum cleaners and sewing machine. I found out that machines, like cars, need tune ups. Happy Sewing!

Aug 07, 2011 | Bernina BERNETTE 65 Mechanical Sewing...

1 Answer

Makes a squeeky sound when runnung

Check your manual for oiling instructions, it could need a clean and lubrication. Even the newer ones with nylon gears still need to be cleaned regularly.

It also could be the needle being blunt; this will cause a squeek or popping sound sometimes. Change the needle for each new sewing project, ie every 4-6 sewing hours. Really important for good stitching as the needle does the work.

Finally, if neither of these solve the problem, then take it in for a service, all machines benefit from a clean, service and tune up regularly, just like your car.

Jun 12, 2011 | Euro-Pro Shark 80 - 7133

2 Answers

I have my grandma'sewing machine the model number is 43 Do you have any booklet for instructions- I can not figure how to thread it. Any place in Montreal that I could get it tune. Thank you

are you sure the model number is 43
I put that in the search box at & it came up a white 431--which has a free downloadable manual

I would suggest to look in the phone book for a sewing machine repair shop

Dec 01, 2010 | White Sewing Sewing Machines

1 Answer

Tune-up instructions needed

it really needs to be oiled and cleaned in places u cant get to which means it needs to be taken apart by a tech that cleans them, ask me I learned the hard way.......I hadnt used my machine very long by I do use it alot and first it started to get a little louder not a lot but I could notice it.....then it started to mess up a little bit here and there and I always cleaned it oiled where they said blowed it out with the vac and all.......but it still went crazy on me lol, I was doing braclets for my granddaughters scoccer beach blast and had like 20 more to go and it just froze......just I thought it was maybe to hot. Shut it down for the night.......Next day still nothing, had to find someone to take it to...1 and a half hours away I finally found someone, had to leave it........what it needed was oiling where I couldnt get to, and cleaning where I couldnt get it burnt the motor......had to have it replaced, was gone for 2 weeks. UGH....but now she purrrrrrrrs like a kitten again thank god.......I had only used it since December of 08, it was still new......but it still needed a tune up, and I didnt know any better, thought that how bad could it be, so I just kept it real clean and oiled so I thought NOT! Silly me.......2 weeks later and a nice bill and new motor........and Im off time something seems to be off...this baby is taking a ride....I cant afford those kinds of take my advice fine someone even if u need to take a day and drive it somewhere, but dont not do it, inside this baby is lots of boards and things that if u open it u wont get it back together correct, oh ya I did that to and they had to fix that too
:( not a good idea. Machine is worth to much not to fine tune it when it should be, but even if u dont think it needs it cause its new or u just had it done.......think again if it sounds funny.......something is wrong, hope u wont need to find out the way I did....good so happy to have mine home again, didnt know how much I loved it till it was gone lol

May 26, 2009 | Singer Quantum XL-6000 Computerized Sewing...

Not finding what you are looking for?
Sewing Machines Logo

Related Topics:

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Baby Lock Sewing Machines Experts

Tally Girl
Tally Girl

Level 3 Expert

1133 Answers

Jon Piercy

Level 2 Expert

67 Answers

Jim Goldsmith
Jim Goldsmith

Level 3 Expert

2005 Answers

Are you a Baby Lock Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides