Question about Sportcraft Exercise & Fitness

Open Question

Sportcraft tx 4.9 error code 1 - Sportcraft Exercise & Fitness

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: Sportcraft TX 2.5 treadmill - error code 3 - stops

Sorry I dont have the solution but I have the same problem.
Read somewhere that Sportcraft control boards had
a design flaw.

Posted on Dec 20, 2009

  • 1212 Answers

SOURCE: location of speed sensor on sportcraft tx 400 treadmills

It is a simple magnet and Hall effect transistor if you have 2 small wires. It usually attaches to the 1/8 inch mini plug. You can test it with an analog meter, the resistance will be stable at rest, and with treadmill in motion, the resistance will change as the magnet passes the hall effect switch. moving the track at slow speed manually will be enough to see the needle move. Speed is calculated off of the rate of those pulses.

Posted on Jan 23, 2012

mendi593
  • 65 Answers

SOURCE: sportcraft tx 2.5 banging noise

where is the noise coming from? the deck, motor compartment, etc?

Posted on Jul 13, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We picked a TX 440 from a friend and the error button shuts it off


If you wish to get some details About treadmill repair; check the site linked here. Pull up older posts.
http://electro-medical.blogspot.com/

Sep 11, 2016 | Sportcraft Tx 455 Sportscraft Treadmill...

1 Answer

Sportcraft tx 2.5 shows code 3 and stops after a few seconds of running time.


If you wish to get some details treadmill repair and error code ; check the site linked here. Pull up older posts.
http://electro-medical.blogspot.com/

Sep 07, 2016 | Sportcraft Exercise & Fitness

1 Answer

Where can I get a console-mother bo9ard for a Sportcraft TX 420 treadmill?


Assuming it is not a beanbag chair/treadmill, I suggest contcting Sportcraft directly for their input on where to obtain the board.

Jul 10, 2014 | Sportcraft Furniture

1 Answer

Tx 5.o rc sportcraft treadmill varies in speed with or w/o load.


1) adjust the speed sensor, see the diagram attached, test for open or faulty. clean it very well. tight the connector very well

2) LUBE the treadmills very important . do it with silicone or wax. Read your onwer manual for verification.

God bless you58dd9ed5-0a2a-43ca-a957-5273338ca4c3.gif

Jun 03, 2013 | Sportcraft Tx5.0 Tx 5.0 Rc Treadmill Motor...

1 Answer

Error code E0


1) adjust the speed sensor see the diagram attached. tight the cable, and clean it.
2)test the input voltage motor, if there are the motor need repair.
3)test the output voltage from the motor controller, for input voltage motor if there are NOT the motor controller need replace.
God bless you
11_8_2012_4_20_13_am.gif

Nov 08, 2012 | Sportcraft Tx2.5 Tx 2.5 Treadmill Motor...

1 Answer

Sportcraft tx 2.5 banging noise


where is the noise coming from? the deck, motor compartment, etc?

Jun 16, 2012 | Sportcraft Exercise & Fitness

1 Answer

I have a sportcraft tx 2.5 and was cleaning it and some water got into the housing where the motor and circuit board is located. Now all I get is the number 7 on the display and it won't run.


Dear Sir:

1) Please unplug the machine
2) Put with air gum machine, and pass in all board and circuit for heating.NOT OVERHEATING.
3) Wait for 24 hours. if you have some infrared lamps, will be better.NOT OVER EXPOSED.
4) Turn ON the machine, and proof, if the problem remain, the board is faulty. and replace.
5) However try to RUN the software calibration for better diagnose, troubleshooting, and fix it. see the block diagram attached.
God bless you
6_10_2012_12_47_33_pm.gif

Jun 09, 2012 | Sportcraft Tx2.5 Tx 2.5 Treadmill Motor...

2 Answers

Location of speed sensor on sportcraft tx 400 treadmills


It is a simple magnet and Hall effect transistor if you have 2 small wires. It usually attaches to the 1/8 inch mini plug. You can test it with an analog meter, the resistance will be stable at rest, and with treadmill in motion, the resistance will change as the magnet passes the hall effect switch. moving the track at slow speed manually will be enough to see the needle move. Speed is calculated off of the rate of those pulses.

Jan 23, 2012 | Sportcraft Exercise & Fitness

1 Answer

Sportcraft TX 2.5 treadmill - error code 3 - stops after a few seconds of operation. ??? Thanks for any advice


Sorry I dont have the solution but I have the same problem.
Read somewhere that Sportcraft control boards had
a design flaw.

Jun 28, 2009 | Exercise & Fitness

Not finding what you are looking for?
Exercise & Fitness Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sportcraft Exercise & Fitness Experts

John

Level 2 Expert

125 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Brad Brown

Level 3 Expert

15557 Answers

Are you a Sportcraft Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...