Question about Car Audio & Video

Open Question

Al encemder mi autoestereo kenwood kdc 248u aparece protect

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: protect mode

Press reset button (small circular button need something with a point) to the left of the 1 channel

Posted on Feb 28, 2009

Ad
smarthome2
  • 1114 Answers

SOURCE: kenwood kdc-438u stuck in protect mode what do i

Disconnect all speaker wires at the receiver and turn it back on. If it does not go into protection, your receiver is ok. Re connect speakers one at a time and test until your receiver goes into protection, then trace the speaker wire to the speaker for cuts or shorts. If you have a multimeter, switch it to ohms and check the speaker for a dead short, you may have a blown speaker. Hope this helps.

Posted on Sep 27, 2009

  • 1 Answer

SOURCE: how can i deactivate the protect that blinks in my

Disconnecting the terminal will take to much time.. In between the skip button ,and the #1 on your stereo there is a little dot. Barely noticable unless you know what your looking for, take a safety pin or a screw( anything with a little tip) and push it in. This will restart your stereo. (Car Must be on)

Posted on Feb 12, 2010

  • 40 Answers

SOURCE: Kenwood kdc-bt742u flashing protect and no sound

If protect is coming up on the display, it means the system is detecting a short somewhere on one of the speakers and so is turning the amp off to avoid damage.
Check all the connections at the back of the amp to ensure they are not shorting, and at the back of each speaker, if nothing is found there, check each wire for damage, or a bare wire touching the body of the car

Posted on Mar 25, 2010

  • 12 Answers

SOURCE: kenwood kdc-mp208 stuck in

Protect indicates that there is a short or a grounding problem usually within the speakers2_bing.gif or the speaker wiring. Locate and press the reset button (pinhole). If protect comes back then disconnect all speakers, reset and connect them back one at a time until protect shows up again. This will help you find out where the unwanted DC signal is coming from. If protect shows up when all speakers are disconnected, then it may need service.

Posted on Apr 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Compr? un Radio Kenwood KDC-X300,cuando programo la hora,la fecha,dem?s funciones,apago mi carro,lo vuelvo a prender,el radio aparece en standby┬┐?lguien de ustedes me podr?a dar una respuesta?


Mi Espa?ol no es my biene ,perdone. Suena Como que lo tiene connectado all ignition solamented. Se nececita conectar el alambre de Acc. A la batteria directamente Para que Guarde la memeoria . Ay beses que se Idica el alabre en question con color azul. Hope it helps Buena suerte,

May 16, 2016 | Cars & Trucks

1 Answer

Why does stereo say protect


Check if a speaker wire come off or some other wire, That will cuase it to go into the protect mode,Allso if you have a amp hooked up to it, End continully have the music cranked up the system will over heat ,That can cause it allso to go into protect mode, There is a reset button on the face plate but it is not marked,

Nov 02, 2012 | Kenwood KDC-248U In-Dash CD, MP3, WMA Car...

2 Answers

Por que aparece la palabra protec en mi auto estereo


ese error se ignifica un corte a tierra en las lineas de bosinas o impedencia muy baja (< 3 ohm). el estereo apaga el amplificador interno para proctejerlo.

Mar 04, 2011 | Kenwood KDC-MP238 CD Player

4 Answers

How do you reset this deck


There is a reset button on the left front of the deck>

Feb 16, 2008 | Kenwood KDC-MP2035 CD Player

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4862 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

The Knight
The Knight

Level 3 Expert

74251 Answers

Are you a Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...