Question about Plumbing

1 Answer

Water house pump not working

Onga pump not working, hard to reset, no leaking water

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,368 Answers

More information would be helpful. Did it freeze? Why is it hard to reset, is it because you did not waite a few minuts befoe resetting.

Posted on Jun 13, 2014

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 832 Answers

SOURCE: onga jsp 130 leaks

It is leaking due to a defective mechanical seal. It needs to be replaced. To replace it, is to take the pumpcase
off by taking off the bolts that hold it. Then, take the impeller off to take the mechanical seal behind it. Put the replacement in, and reassemble the pump. Just get in touch with us by e-mail to get more assistance.

Posted on Oct 27, 2009

  • 541 Answers

SOURCE: onga water pump not pumping water thru to house

either water lock or motor burnt out ,

Posted on Mar 20, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Im on tank water using a onga pump, loss of water pressure at taps,how do i get it back tanks full, whole system is only 6mths old,thanks


check for a blockage at the pump inlet or outlet from the tank
(leaves, animal etc)
check that the motor is running at full rpms ( problem start/run capacitor--no guaranteed life of capacitor)
check for water leak after pump

Mar 31, 2016 | Plumbing

1 Answer

Onga 4352 Spa Pump is leaking from the opening in the bottom of the pump. I have opened it & siliconed the Oring seal but it continues to leak. Any suggestions?


I had a new pump brought to me once that continued to leak after replacing the shaft seal three times. Careful examination revealed a sand casting fault in the pump body. The water was leaking through the body of the pump. Have you replaced the shaft seal?

Nov 04, 2014 | Plumbing

1 Answer

Onga house water pump


It sounds like the starting capacitor has failed. It is the round thing with two wires normally mounted on the outside of the motor. There is also a starting switch that could have failed but it is eaiser just to try the capacitor first.

Jan 21, 2014 | Plumbing

1 Answer

Onga water pump not pumping water thru to house


either water lock or motor burnt out ,

Mar 17, 2012 | Plumbing

1 Answer

My electric onga water pump which pumps water from my watertank to the house will not turn off. I have looked for a leak but cannot find one.


What is the model of the pump? What type of control does it have - pressure switch, electronic controller or what?

Jul 30, 2011 | Computers & Internet

1 Answer

Have an Onga JJ400 jet water pump several years old, pump is working but delivering poor water flow


Is the pump building pressure and shutting off? If the pump keeps running but not building pressure than there is most likely a problem with the well (low volume). Also check for a water logged bladder tank.
RJ

Jun 29, 2011 | Plumbing

1 Answer

I have an Onga smh45 which keeps tripping out and you have to push the reset button. I have had it in to two repairers and they say they can't find anything wrong with it. Any assistance would be...


This could be your problem. Make sure it isn't running dry.
D.R.O.P (Dry Running Over-Temperature Protection)
The Onga SMH series of pumps (excluding the SMH35) are fitted with the internationally patented D.R.O.P system which protects the hydraulic parts from possible damage that can be caused by overheating of the liquid inside
the pump casing. The overheating can be the result of external causes (outside the pump) or occurs because the pump stops priming and as water is pumped out the
pump runs dry.The D.R.O.P system is reset using the switch located on the condenser.
If you have access to an amp meter, measure the curring when pumping full load, and be sure it is less than the full load amperage listed on motor.

Aug 10, 2010 | Plumbing

1 Answer

New onga JS120 pump worked fine for 4 months bringing water from tank up to house then suddenly stopped.We undid the pipe and reconnected it,the pump worked again but stopped again after a few...


a number of possibilities like insufficient pressure in the bell or pressure leak 'or pump motor dying
but i'd be looking at a warranty claim

May 11, 2010 | Plumbing

Not finding what you are looking for?
Plumbing Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plumbing Experts

Donni Steen

Level 3 Expert

659 Answers

Brad Brown

Level 3 Expert

15451 Answers

Tom Chichester

Level 3 Expert

33294 Answers

Are you a Plumbing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...