Question about Stanley Tools Hammer Staple/Tacker - PHT150C

Open Question

Stanley fatmax hammer stapler instructions - Stanley Tools Hammer Staple/Tacker - PHT150C

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 122 Answers

SOURCE: How to basically operate my

Press the red button - (distance) you will see a red dot on the wall you are measuring - then you will hear a beep - release the button and read the display - the measurement should be displayed and accurate within a quarter inch.

Posted on Nov 23, 2008

  • 1 Answer

SOURCE: Just purchased a Stanley FatMax 10-778 retractable

1. Make sure the side lock is unlocked.
2. Push the thumb tab all the way to the front of the blade handle.
3. Insert the blade in the opening, you may notice two notches on the top side of the blade.
4. Press the small blade release button as you slide the blade into the knife. You may have to jiggle up and down to get the two notches on the blade fully into the handle.

If properly inserted, the exposed area of the blade should look very close to an equilateral triangle.

make sure both notches of the blade are inside the handle. They notch into the thumb lever.

good luck

Posted on Apr 11, 2010

Testimonial: "Thanks so much!"

puertobori
  • 7733 Answers

SOURCE: Just purchased a Stanley fatMax

Some models has 2 screws on the knife case.unscrew them and you can access to the blade.

Posted on Nov 08, 2010

  • 127 Answers

SOURCE: Need manual for stanley electric stapler model

here is a link to the manual

http://homeappliance.manualsonline.com/mdownloads/f2624d76-9579-4c12-a9f1-22eab6ac3388.pdf

Posted on Dec 27, 2010

  • 27 Answers

SOURCE: I cannot figure out how to put a blade in my

at the handel end it will pull apartthen slide the whats left of the old blade and put new won in its place just do it slowly so you dont forget how it goes

Posted on Apr 21, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I calibrate a FatMax digital level?


Mark, Automatic calibration, check the little pockets on case instructions inside, the instructions show how.
Check the attached links,
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

Stanley FatMax Digital level mp4

Stanley fatmax digital level instructions Measuring Tools Measuring Tools

STANLEY HAND TOOLS Measuring Leveling Layout Levels Stanley FatMax Digital...

http://www.microprecision.com/equipment/STANLEY-CALIBRATION.html

Mar 04, 2016 | Measuring Tools & Sensors

1 Answer

Where can I download the instruction manual for a stanley fatmax 450 amp jumpstarter?


Request the manual directly from Stanley. It may not be available as a download.

Jan 12, 2015 | Stanley Measuring Tools & Sensors

1 Answer

How can I get a parts repair manual/list for a stanley fatmax 3.8 cfm compressor


try searching for stanley fatmax compressor . I think bostitch owns it

Nov 03, 2014 | Measuring Tools & Sensors

1 Answer

My Stanley PHT150 is jammed and I cannot remove the staple channel. The instructions do not address a jammed staple channel so, how does one remove it?


Hi Dave,

Nice and easy this one.... all you've got to do is remove the chrome coloured pin at the handle end. This then allows the magazine to be removed by pulling it from the front end. Just make sure that you've removed the pusher (Where you feed the staples in) from the back first

Sep 18, 2014 | Stanley PHT150C] SharpShooter Heavy Duty...

1 Answer

Instructions stanley fatmax staplegun


Don't know what model you have but these instuctions should be pretty typical.

PHT350 Hammer Tacker Instructions

Aug 18, 2014 | Measuring Tools & Sensors

1 Answer

I NEED AN INSTRUCTION MANAL FOR STANLEY CL2


You should be able to get information from Stanley Black and Decker

Apr 08, 2013 | Cross Cst Stanley No.CL2 Fatmax Line Self...

1 Answer

Instruction for Stanley FatMax Stud Sensor Finder 400 (77-730)


Please people dont waste your money but a cheap standard one Stanley 77-730 stud finder is bad does not work at all , miss my old cheapy never failed me

Mar 05, 2012 | Stanley Measuring Tools & Sensors

1 Answer

Door springs, part no. H286, for a Bostitch H2B stapler


Parts for the Bostitch H2B Hammer Stapler can be purchase from MJS Floorcoverings Manfield Brisbane

Dec 16, 2009 | Stanley Hand Tools

1 Answer

How to basically operate my stanley fatmax, TLM100. The directions that came with it were for another Stanley product. Thanks,Ralph


Press the red button - (distance) you will see a red dot on the wall you are measuring - then you will hear a beep - release the button and read the display - the measurement should be displayed and accurate within a quarter inch.

Nov 16, 2008 | Stanley 100 ft. Tape Measure, FatMax

Not finding what you are looking for?
Stanley Tools Hammer Staple/Tacker - PHT150C Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Stanley Hand Tools Experts

Jim Thurston

Level 3 Expert

670 Answers

Ivan
Ivan

Level 1 Expert

35 Answers

Don Numinen
Don Numinen

Level 2 Expert

62 Answers

Are you a Stanley Hand Tool Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...