Question about Tefal UltraGlide Easycord FV4256 Iron

Open Question

Light but no heat produced by temperature slide

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heat element light comes on (so there is power) but the iron will not hear up


The Delonghi Pro300 has two thermostats that contact the boiler. One is a low temperature thermostat that allows the boiler to heat up to 145 degrees (F). The other turns off the boiler when the temperature reaches 180 degrees. It sounds like your low temperature thermostat has failed. The part can be ordered on line. You need to have good basic mechanical skills and the proper sized star screwdriver to replace it.

Apr 24, 2014 | DeLonghi Stiromeglio Compact PRO 300 Iron

1 Answer

The temperature of the boiler is not controlled normally and the safety valve opens. I suspect that the temperature control sensor is not functioning properly, and if this is the case where can I find a...


see this causes and use the common sense. God bless you
If the iron heats but steams improperly, inspect the soleplate and clean the vents (see below) and flush sediment out of the steam chamber (see below).
If the iron produces too much or too little heat, test the electrical cord . Also test and, if needed, adjust calibration of the thermostat (see the Appliance Controls Fix-It Guide).
If the iron does not spray properly, inspect and clean the nozzle (see below).
If the iron leaks or spits, clean the steam vents, nozzle, and tank.
If the iron sticks to fabric, clean or repair the soleplate. If the iron stains fabric, clean the soleplate, clean the tank with a commercial cleaner, and use distilled or filtered water.

9_20_2012_11_55_37_am.jpg

Sep 19, 2012 | Rowenta Irons

1 Answer

MORPHY RICHARDS 42256 JET STREAM STEAM GENERATOR IRON does not provide steam


My MORPHY RICHARDS 42256 JET STREAM STEAM GENERATOR IRON has stop producing steam. I have changed the filter and although it heats up, it does not produce any steam.

Feb 29, 2012 | Irons

1 Answer

Why light blinks then goes off when switch is still in the on position


The thermostat in the iron controls the temperature of the iron. The red light indicates when the power applied to heat the iron which is set by the temperature dial on the iron. When it reaches the correct temperature the thermostat turn off the power and that is when the red light switches off.

Jan 15, 2012 | Irons

1 Answer

Good day I have an euro pro iron and it leaks all the time leaving water on washed clothes.also it leaks out of the bottom??


The water may come out at the bottom instead of steam. this is due to insufficient heat produced. So switch on your ironbox and keep it in full temperature using the knob. then the water will be coming out as steam and not as water itself. Try again.


I hope this is useful to you
Thanks

Jun 27, 2010 | Sunbeam Euro Press 4045 Iron

2 Answers

Iron producing lots of water


Hi,
Here is a tip that will help you with that problem...

My Steam Iron is Leaking Water
http://www.fixya.com/support/r5301301-steam_iron_leaking_water

heatman101

May 18, 2010 | Philips GC 8220 Iron

1 Answer

Switch light goes on when pressed but goes off if not pressed


Switch light goes on when pressed but goes off if... OR iron does not heat at all even pressing the button to turn it on continually.
Don't understand which one question you are asking
But if there is no heat at all after switching it on, it needs to go to iron heaven but be sure to cut the plug of the end, Saftey reasons at the dump. BUT if lights are coming on the iron is working. the large dial on the water filler is temperature control. Turn this around to cotton or linen.
The light will come on and off while in use, it allows you to know that the iron has cooled and is going back to your select temperature( on the large dial)

Make sure that you use water in the iron as it will aid your ironing and make it quicker. Make sure that the iron temperature dial on the water filler is at the correct temperature for the item that you are ironing.
Hope this helps

Sep 17, 2009 | Black & Decker Steam Xpress AS250 Iron...

1 Answer

No Steam From Iron


Hi,

I can tell you the stem rod for the steam control is choke or faulty. These prevent the water going onto the sole plate that why no steam.You've to send for servicing at your nearest repair shop or agent.



Rdgs
alan

Jan 10, 2008 | Rowenta Professional DE880 Iron

Not finding what you are looking for?
Tefal UltraGlide Easycord FV4256 Iron Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Tefal Irons Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18394 Answers

Henry  Thomas
Henry Thomas

Level 3 Expert

1074 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

Are you a Tefal Iron Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...