Question about Whirlpool Duet GHW9150P Front Load Washer

2 Answers

Control panel the control panel on the washing machine is stuck on controls locked how do I fix this so I can do laundry

Posted by on

  • 1 more comment 
  • robertasue May 25, 2009

    control locked

  • Anonymous May 25, 2009

    the washer says "control panel locked"...how do it get it to release?

  • dw1963 May 26, 2009

    the control panel on the washing machine is stuck on controls locked how do I fix this so I can do laundry, same issue as mltaylor07, can anyone help?

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Select and hold END OF CYCLE SIGNAL for 3 seconds untill the CONTROL LOCKED status
light turns off. The button you need to hold down is under the louder, softer, and off volume
control buttons.

Posted on May 27, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 6,784 Answers

Unplug or shutdown the circuit breaker for 5 minutes. this will reset the control. if the control remains locked after you power this unit back up after the five minute reset has been initiated, this will confirm a major control fault and you will need to replace the control board in this case.

Posted on May 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Smeg washing machine error 7


F 7 usually means a stuck circuit in the touch control. In laundry it pertains to the door lock release function.

May 08, 2011 | Washing Machines

2 Answers

I was doing a load of laundry and the washer "froze" i tried to cancel the load but it wont stop.... i ended up unpluging it and even when i plugged it back in its still stuck!!!


Locking controls
The Control Lock prevents unintended use of the washer. You
can also use the control lock feature to prevent unintended cycle
or option changes during a cycle. When CONTROL LOCKED is
lit, all buttons are disabled. You can lock the washer while it is
operating.

To lock the controls
Select and hold END OF CYCLE SIGNAL for 3 seconds.
The CONTROL LOCKED status light glows.

To unlock the controls
Select and hold END OF CYCLE SIGNAL for 3 seconds until the
CONTROL LOCKED Status light turns off.

Nov 10, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

I am doing a load of laundry the washing machine maytag neptune


This means locked rotor. you have a bad motor control unit. take the door off by removing the 4 screws also take the side/front panel off. You will see the motor control board. Do you have a delay wash cycle? If you do set it to delay wash remove the jp4 connector if the unit tumbles on it's own then the motor controller is fine but if it does not then you have a bad motor control board. Check it out and let me know. also there is a fuse on that board if you can locate it and check for continuity that will also help diagnose it. MAKE SURE YOU UNPLUG IT FIRST THOUGH!!!!

Jun 04, 2009 | Maytag Neptune MAH6500A Front Load Washer

1 Answer

Locked


find button with lock emblem underneath hold in for 3-5 sec should release control panel lock may be no good reason but they have been known to lock because they want too remember your dealing with a computer any random signal may cause this if all elese unplug for 20-30 min and retry

May 19, 2008 | Whirlpool GHW9100L Front Load Washer

1 Answer

Control lock


Try pressing and holding the "End of Cycle Signal" button at the bottom right corner of the control panel. This works for me!

Mar 30, 2008 | Whirlpool Duet GHW9150P Front Load Washer

11 Answers

Whirlpool duet


On the far right sode of the control panel there is a unlock control reset button. Hold it for 3 seconds and the fault will clear.

Mar 18, 2008 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Kenmore HE4t Washer stuck in "controls locked" mode


you need a new cpu you can unlock door by removing bottom panel reaching up to the door lock and pulling a little ring on the bottom will manualy unlock the door

Nov 08, 2007 | Kenmore 3.8 cu. ft. HE4t Front Load Washer

1 Answer

Washer won't run....


It seems as an overload issue. The machine has an overload switch to protect the motor. Take the comforter out and operate the machine,it should work fine. Good luck!

Sep 10, 2007 | Frigidaire GLTF2940ES Front Load Washer

Not finding what you are looking for?
Whirlpool Duet GHW9150P Front Load Washer Logo

527 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Sal DeAngelo

Level 3 Expert

2183 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...