Question about Computers & Internet

4 Answers

No signal i buy a new motherboard for my pc but did not send signal ti my monitor what you think could be the problem?

Posted by on

  • 3 more comments 
  • Avi Manor Dec 22, 2007

    I am using an Intel E210882 board.
    The on board video is completely dead.
    How can I disable it and place an alternative video card?
    avimano@gmail.com

  • OldDaddog Jan 01, 2008

    Inserted network card from another computer. After that no video and no beeps. Removed card, removed video card and tried on board video, disconnected hard drive and DVD drive, reseated memory dimm. still no video.

  • Anonymous Jan 20, 2008

    I just got a new ECS 945G-M3 board and i get no video signal also.

  • Anonymous Apr 28, 2008

    replaced vdeo card

  • Anonymous Mar 05, 2009

    how do i enable the video card instead of the video card that is on the motherboard?

×

Ad

4 Answers

49p1605

Posted on May 31, 2008

Ad

49p1605

Posted on May 31, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Driver video controller

Posted on Mar 28, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 883 Answers

On-board video? enable it in BIOS setup
video card instead....try re-seating it.

Posted on Oct 19, 2007

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Monitor says no signal tried on my lap top and monitor works. Put in new video card still says no signal


got the same pc,the video interface chip on mother board has blown,common fault with this pc,replace motherboard is option 1 option 2 buy a new pc

Sep 17, 2011 | Acer Aspire M1641-U1521A PC Desktop

2 Answers

Monitor all plugged in all cables fine when pc boots up monitor power light come on and screen says "no audio visual signal" help!


Does your computer have more than one location where the video-cable can be connected?
If so, connect to that alternate location.

Try connecting the monitor to a laptop, to see if the laptop can send a signal to the monitor.
You might have to "toggle" the laptop (internal-screen-only / external-screen-only / both-screens)
to activate the external screen.

Feb 17, 2011 | Microsoft HannsG HU171D 17" LCD Monitor

1 Answer

I have gigabyte GA-G41M-ES2SL rev 1.1 motherboard with 2 GB RAM, 350 GB SATA HD, and SATA DVD-ROM. My PC die yesterday. i check it. there is no electricity to my pc, i think my Power supply (380W) was...


hey yo, i think your problem is quite similar to my problem. Because after I've installed it properly and after 5 hours working the screen suddenly become blank and not detect the connection. I think the mobo already broke down.. T_T

Dec 20, 2010 | Gigabyte GA-G41M-ES2L Motherboard

2 Answers

Monitor (no signal) after replacing mother board and CPU


try only connect Monitor and keyboard, and check for booting (disconnect all the rest (HDD, CD DRIVE, Sound Card, Network Card, ....) then try connect one by one and always off to change hardware config.

If dont work with monitor and keyboard, try reset bios(jumper),check again, then replace memory modules (must be compatible to new motherboard), evan dont work, send back the motherboard for defective motherboard.

Jan 14, 2010 | Gateway Intel (El Paso 2) Motherboard P4...

1 Answer

Brand new Monitor blank screen says No Signal


There is nothing wrong with the monitor. The LCD is not recieving any signals from the PC. Either you are connecting the VGA cable incorrectly or your VGA card is not set from the PC BIOS. The VGA cable might also be faulty.
Recheck that all the connections are clean and secure. If you are using a PCI-E or AGP card, the computer BIOS should be set to send the video signals through the PCI-E or AGP card. Follow the procedure in your motherboard manual.
If your pc has on-board graphics then you should connect the VGA cable to the on-board VGA out connector.

Oct 19, 2009 | Acer X203H bd Monitor

2 Answers

When I turn on my pc I an see the hard drive light working and flashing, indicating that it is loading up, but my monitor does not receive any video signal,so I hooked my pc to my freinds monitor and I got...


Sounds like your video card is bad. You will need to purchase a new one. On some machines there is 2 video connectors -like 1 on the motherboard and 1 other mounted in a slot just verify that you have tried both connectors if you have them before buying a new card.

NOTE: Usually the slot mounted video card will over-ride the motherboard video by default.

Good Luck!
Rich

Jan 30, 2009 | E-Machines eMachines Desktop PC

2 Answers

No Signal


No signal on screen means that there is no input for your monitor from the PC.

1. There might be problem in your PC or in the cable connected to PC from monitor.
2. Your PC might damage that it could not send signal to the monitor.
2.1 In your Motherboard might be faulty in the VGA chips.
2.2 In your Motherboard's SMPS mean power supply.

I think you can got my point. If you are tech person it will help you, otherwise you should take a tour to any service centre.

Thanks & Goodluck
Iqbal

Jul 21, 2008 | Intel Desktop Board D845GLVA...

1 Answer

No signal


have you tried different video card? try to use the onboard videocard of your motherboard and securely tighten the vga/hdmi cable.

Jun 11, 2008 | PC Chips Computers & Internet

1 Answer

Emachine W1135


when ur starting the tower and it light are on and ur fan there is no problem with the power supply, i think that u rily need a new motherboard because ur board will not boot on start up..

Oct 17, 2007 | AMD eMachines Desktop System w/ 17'' CRT...

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

571 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18425 Answers

Alun Cox

Level 3 Expert

2678 Answers

David Payne
David Payne

Level 3 Expert

14162 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...