Question about Bh Fitness Exercise & Fitness

Open Question

Treadmill error code

Error e3

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ercupa190
  • 12223 Answers

SOURCE: I cannot lower my Pro Form Treadmill 725 TL to the lowest position for storage

Watch the videos:
http://www.youtube.com/watch?v=TquYcOzGIw4&feature=related

http://www.youtube.com/watch?v=9G4MZh8JO2Q
http://www.youtube.com/watch?v=M7qJrRbdfBc
http://www.youtube.com/watch?v=MIIxoPtvhy8hthttp://www.fixya.com/support/r10724803-measure_voltage_in_transforme_fitnesshttp://www.youtube.com/watch?v=bF3OyQ3HwfU&feature=relatedSome system has board relais: one for DOWN AND ONE FOR UP: Please a) test for open and close the relais b) clean the contacts with spray contact cleaner and test. If the relais ARE not closing or oping the board is faulty.
See the block diagram.
12_6_2011_6_04_05_pm.gifGood luck, sincerely. G-d bless you, if you need additional help, please reach me.

E.CUADRA
MANAGUA, NICARAGUA. C.A

Posted on Dec 06, 2011

ercupa190
  • 12223 Answers

SOURCE: Treadmill FN 10282 shows code E3

Try to RUN the software calibration for diagnostic, troubleshooting and fix it.
2( However LUBE the deck belt, very IMPORTANT
3) LUBE the rollers bearing too.
4) Test the input voltage motor, if there are the motor need repair, see my persona TIPS.
5) test the output voltage board, for input voltage motor, if there are NOT the board is faulty. see the block diagram
God bless you
9_21_2012_12_58_10_pm.gif

Posted on Sep 21, 2012

ercupa190
  • 12223 Answers

SOURCE: what does an E3 error code mean on my vitesse endurance xt treadmill

"E03': No sensor signal. Sensor wire is faulty, replace the sensor wire. Magnetic sensor wire is not working replace see the diagram attached.However clean it. and tight the connector very well.God bless you
a385b520-531b-490b-b4e8-01a09d11ff5e.gif

Posted on Apr 04, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My reebok irun treadmill suddenly stops with E3 error code displayed can you help me please.


Try lubricating the belt. My treadmill requires lubricant every now and then. Its not your treadmill but a treadmill is a treadmill. That's what stops the belt from slowing down due to friction. Go to your nearest Gym they may be able to sell you a tube of lubricant. Good Luck

Oct 23, 2016 | Reebok Exercise & Fitness

1 Answer

How to fix Error Code E3 on Schwinn 6710P treadmill


If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/
http://electro-medical.blogspot.com/

Jul 30, 2015 | Schwinn Exercise & Fitness

1 Answer

Precor treadmill code e3 is on


Precor Error 03, Memory, RAM, EEPROM Test Error Probable Cause This error message almost always indicates an upper PCA problem when it is consistently displayed. Failures causing this error message to be displayed are rare.
Corrective Action If the error message is consistently displayed when the unit is powered up, the upper PCA should be replaced. It is possible to see this message displayed intermittently due to external causes. If the units A.C. input significantly dips during the power up test sequence the test could fail resulting in this message being displayed. Treadmills operating on non-dedicated A.C. circuits may see this message displayed on an intermittent basis. Precor Error Code 03 E03 EEPROM Test Error

Oct 18, 2013 | Precor C954 Remanufactured Treadmill

1 Answer

What does an E3 error code mean on my vitesse endurance xt treadmill


"E03': No sensor signal. Sensor wire is faulty, replace the sensor wire. Magnetic sensor wire is not working replace see the diagram attached.However clean it. and tight the connector very well.God bless you
a385b520-531b-490b-b4e8-01a09d11ff5e.gif

Apr 03, 2013 | Exercise & Fitness

3 Answers

Hi, i have an Error signal " 2 - 9 F " the treadmill stops and cant run anymore. thanks a lot!


I have a Matrix Treadmill t4. An error of "E1 and E3" occurs when it is started? Can you tell me the solution?

Mar 15, 2011 | Matrix T3Xi Treadmill

1 Answer

I havea new balance 1400 I keep getting two error codes on my screen the first is E1 and then A E3 on elevation.?


Hi This is dinesh here,

The E1 Error is for the sensor problem and the E3 error is for the IC crasg in the machine...

Jul 22, 2010 | New Balance 1400 Treadmill

1 Answer

Error code E2


Hi most of the treadmill with e2 error code are related to the motor speed sensor so check the sensor

May 12, 2009 | Exercise & Fitness

Not finding what you are looking for?
Exercise & Fitness Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bh Fitness Exercise & Fitness Experts

Shehu Pro
Shehu Pro

Level 3 Expert

1284 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Tom Chichester

Level 3 Expert

34170 Answers

Are you a Bh Fitness Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...