Question about Pioneer PDP-4360HD 43 in. Plasma Television

Open Question

My pioneer plasma smw1985-A goes into standby mode (blue blinking light) while I'm watching it. When I turn it off it turns back on in stand by mode

Plasma tv goes into stand by mode while tv is on. The blue light starts blinking with no picture. I turn the tv off. Then the tv goes into stand by mode again

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: pioneer plasma tv

Hi, you see when a TV set is left without power going through it, it actually does it harm, things in storage should be powered up at least a few times a month, otherwise the capacitors will loose their "Form" and will not work correctly, and if left too long the unit simply becomes unservicable, also the moisture in the atmosphere, gets absorbed by osmosis, into "Other" compnentry, and this too causes failures, not to mention, any other sort of corrosion, or perhaps flat cells in a unit, inductors etc. So as said, this makes a unit more or less unrepairable.
Below is a service manual, http://www.elwinelectronics.com/roadscum/Field_Service_Guide_07_rev1.2.pdf
http://www.avsforum.com/avs-vb/showthread.php?t=763359

Posted on May 04, 2010

  • 7 Answers

SOURCE: my pioneer plasma tv in standby mode and wont turn on

Try restting it by unplugging the tv for a few mins and it should rest to original factory default settings but leave it unplugged 10-15 mins to be sure.

Posted on Dec 18, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Media receiver "on" button flashes 8 times and turns the Pioneer TV to standby.


These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. http://electronicshelponline.blogspot.com/

Oct 14, 2015 | Pioneer Televison & Video

1 Answer

Find activation code for pioneer


My pioneer 5020FD Kuro tv. when I plug power to the unit, a blue light blinks 8 times pause 2 sec. and blink 8 times repeating this and if i press power button it clicks red light and makes a clicking sound and goes back to the blue light blinking again, it did this once before and the picture came on fine until i turned it off and now it just blink the blue code.

Dec 10, 2014 | Pioneer PDP-5020FD 50 in. Plasma HDTV

2 Answers

My 15 month Celcus LCD423D913FHD tv will not turn on. The standby light is lit and will flicker but will not power up the tv. What is the likely problem?


Fault with its main board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/ . In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.

Oct 20, 2014 | Televison & Video

1 Answer

My pioneer plasma tv in standby mode and wont turn on


Try restting it by unplugging the tv for a few mins and it should rest to original factory default settings but leave it unplugged 10-15 mins to be sure.

Dec 18, 2011 | Pioneer PDP-4270HD 42 in. Plasma...

1 Answer

When power turn on tv goes in to standby mode when you press standby button on the remote control for split second the blue comes on then goes back to standby mode


Hi these pioneers are difficult to work on you are better off taking it to a technician you will save a lot of headaches trying to fix it. If you still want to do it the first thing I would suspect is teh siganl board.

You can get parts for this tv at www.interliquidparts.com

Dec 18, 2011 | Pioneer PDP-4270XD 42 in. HD-Ready Plasma...

1 Answer

Red LED lights


power supply shot ... sometimes x board or y board

Oct 02, 2009 | Pioneer PureVision PDP-5030HD 50 in....

1 Answer

PIONEER PDP-424MV Plasma TV


Hello,

I have the same TV, well, nearly, PDP434.

The only part I ever sell for these is the main PSU (power supply).

The TV "checks" it self using a self diagnostic system. As soon as it discovers a problem, it shuts down and blinks an error code on the front LED.

It always seems to be the PSU.

I hope this helps at least a bit.

Mar 28, 2009 | Pioneer PureVision PDP-424MV 42 in. Plasma...

1 Answer

Power goes off automatically


The flashing light is not a stand by...that a service light telling you it has a problem that needs to be fixed...

Apr 14, 2007 | Panasonic TH-42PD50U 42 in. Plasma EDTV

Not finding what you are looking for?
Pioneer PDP-4360HD 43 in. Plasma Television Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Televison & Video Experts

The Knight
The Knight

Level 3 Expert

74106 Answers

Jaime Hernandez

Level 3 Expert

2318 Answers

Henry  Thomas
Henry Thomas

Level 3 Expert

1074 Answers

Are you a Pioneer Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...