Question about Jandy Aqualink Rs4 One Touch Control System Control System

1 Answer

Spa wont heat

We have a pool and spa and the spa heat wont come on.

Posted by on

  • debbie nordgren May 20, 2009

    can someone help me figure this problem out

  • SweetTea22 May 23, 2009

    The spa will not heat up AND I keep getting a water sensor opened message

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,902 Answers

Check the pump make sure that it is getting power. If there is power to the pump and nothing is working then pump is bad. Also this could be your computer board is bad, a inline fuse. or the Jandy is bad

Posted on May 20, 2009

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2712 Answers

SOURCE: Pool and Spa Heaters pros and cons

An electric heat pump needs heat available to pump. If it is 30 degrees outside, heating a spa to 102 or so, may be impossible unless the heater has some type of alternative heat source. A properly sized, gas fired heater can take care of a larger range of heating needs. A combination heat pump and natural gas heater, probably with a controller, really makes the issue more difficult, expensive, and would require a lot of study for efficient, cost effective operation. Bottom line: In really mild climates a heat pump might do the job. In cooler climates the gas heater rules. And where a wide range of temperatures and high heat demand is wanted by the customer, a gas heater is the only way to go. A backup heat pump may take years to payout.

Posted on Aug 27, 2008

PartsCenter
  • 125 Answers

SOURCE: can you heat the pool and spa at the same time?

Here is a link to the owners manual and users guide.
Aqualink RS24

Posted on Mar 04, 2009

rcampsr
  • 90 Answers

SOURCE: Heater cycles on and of, pool/spa does not reach desired temp

hello, It sounds like you may not be getting circulation thru the heater. Make sure the valves are open to allow water to pass thru the heating system. Some systems use a bypass on the heater so there is not a lot of wear on the coil system in the heater. If it is not circulating it will get too hot and the safety shut down will occure. If you are getting water circulating thru the heater, then the thermocouple or auto start igniter system is not working correctly. It is trying to start and can't then recycles. If the burners are igniting on the startup and then shutting back down you may have a bad control unit or thermal sensor unit. Since the unit is gas have a professional service it for you. Good Luck, RAC

Posted on Apr 20, 2009

  • 990 Answers

SOURCE: Purex Triton Minimax 400 pool/spa heater not igniting

This sounds like you have a problem with your pilot. You can check this with a small mirror to see if their is a spark when you turn it on. If you have any soot build up on the pilot that will stop the spark and keep it from lighting also. If you have a short on your pilot wire this could be the problem also. I hope this helps, good luck.

Posted on Dec 12, 2009

  • 10 Answers

SOURCE: I have a Jandy Laars LX Pool/Spa Heater...when I

If the unit is lighting then shutting off then repeating it isn't rectifying, means not sensing the flame. May have a bad flame sensor or ignition control. I'm guessing your AGS is indicated on the GUI also.

Posted on Mar 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Problem with jandy rs 4. Pool heat pump Is running. We didn't turn it on and the heat pump light on the control panel is not lit


Does your pool gave an attached spa?

IF it does have a spa, dies it also have a spa side remote?
If so the first step would be to unplug the spa side remote from the back of the board.
If the issue stops then you need a new spa side remote if it persists then it nah be be main circuit board or relay for the heat pump.

Nov 01, 2014 | Jandy AquaLink RS 4 P or S OneTouch Pool...

1 Answer

My spa wont heat


sounds like temp sensor is bad not calling for heat

May 18, 2014 | Elite Pool & Spa

1 Answer

Value position to heat pool


turn the valves so ALL the water goes through the heater and back to the pool

Apr 17, 2014 | Hayward Pool Products Pool & Spa

1 Answer

Program my dream maker spa


If it is heating up, it IS doing something!

What do you mean: "Wont do nothing"?

Apr 16, 2014 | Dream Maker Spas Dream Maker SpaDition...

1 Answer

Heater wont heat it says 106 all the time


The thermistor is bad...its job is to read the temperature of the water and transmit it back to the control board. Your replacement part number is 42001-0053S.

John

Apr 22, 2011 | Sta Rite StaRite 400000 BTU Heavy Duty...

1 Answer

Spa used once now wont heat up again


There is something wrong with your water balance and/or your sanitising chemical level.

Dump the water. Get the help of your pool supply place to help you balance the water. pH should be 7.4, Total Alkalinity should be in the range required by your sanitiser (80 to 100 or 100 to 120) and chlorine or bromine should be around 10 ppm CL or 20 ppm BR.

May 16, 2010 | Pool & Spa

2 Answers

I want to heat the pool from the spa. I have the spa and spa heat on but the spillover wont come on when I have the spa on. When I turn the spa off the heat goes off. What do I do


When your system is put into Spa mode the system draws water from the spa only to the heater to keep the spa at temp, this is why the overflow doesn't work and why you can not heat the pool in spa mode. If you could heat the pool this way it would take a very long time, since the spa is smaller then the pool. You can heat the pool and spa at the same time in pool mode. Water is pulled from the pool, heated and goes back into the pool and spa.

Mar 27, 2010 | Jandy AQUALINK RS TELELINK KIT

Not finding what you are looking for?
Jandy Aqualink Rs4 One Touch Control System Control System Logo

Related Topics:

392 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jandy Pool & Spa Experts

David Spradling
David Spradling

Level 3 Expert

3543 Answers

Pj Kiley
Pj Kiley

Level 1 Expert

21 Answers

Bill Jordan

Level 2 Expert

372 Answers

Are you a Jandy Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...