Question about Network Bridges

1 Answer

Reseting hello can some one please help me i have a paradyne modem and i changed the ip on it and it not on dhcp anymore but when i try to log back into the modem the model is 6212-I3-200-0gn

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 155 Answers
Re: reseting

If you change the default address you also need to be sure that you have the DHCP enable and you are not having addresses in conflict.


Please send me what configuration did you change and with what addresses

8e8290a.jpg with another one

Posted on Oct 19, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

I was helping a friend who has Earthlink DSL (a ZyXel DSL modem) to get her Linksys WRT160N wireless router working with the Earthlink modem. No luck. Earthlink won't help unless you pay $7.95/mo with a...

Hello mcneel,

The router should use the ZyXEL P600 as it's DHPC Server. And review/update the ZyXEL WAN configuration as follows:

• Log on to the ZyXEL P600 browser configuration interface:
• Enter username/password: Default is username:admin - password:1234
• Click '+' by Network in the letf-hand panel
• Click WAN
• In the Internet Connection tab, select the following options:
Name - (Any Name)
Mode - (Routing)
Encapsulation - PPPoE
User Name - (ISP login username eg.
Password - (ISP Login password)
Service Name - (Leave Blank)
Multiplexing - (LLC)
Virtual Circuit ID
VPI - (Leave Blank: Issued by ISP)
VCI - (Leave Blank: Issued by ISP)
IP Address
Obtain an IP Address Automatically - ([X] Check this option)
Static IP Address - (Not Selected)
IP AddressI - (Leave Blank)
Nailed-Up Connection - ([X] Check this option)
Connect on Demand Max Idle Timeout sec
• Click 'Apply' button
• Close the browser configuration interface page

Finally, this link to the EarthLink DSL FAQ Setup Installation and Configuration page might offer some useful suggestions:

If this solution is helpful please click a thumbs-up rating below.

Have a great day,

Feb 04, 2010 | Zyxel Prestige 645M (AM408405) Bridge

1 Answer

Same problem with speed stream

when it comes to mac you got to check with the network settings.
If the modem you are using has a DHCP program enabled, then you will have to configure the network settings (configure ipv4) using dhcp
and renew the ip address, if not then you will have to create a manual connection(internet connect) in the same network settings and use your ISP provided user name and the password to connect.
When your internet is connected using internet connected the enet light will be off on the modem

Aug 12, 2009 | Siemens SpeedStream 4200 (13A4200001)...

1 Answer

I want to secure my wireless network so neighbors coannot use it

type your ip adress into you web browser, this should take you to the configuration screen, there should be a tab that says security or something like that, select the type of security that you want, and it should assign you a wireless key automatically, hope this helps

May 15, 2009 | Siemens SpeedStream 4200 (13A4200001)...

1 Answer

Cannot share connection

The IP address that you have is an automatic IP address the Windows generates. It basically means your computer is not getting an IP address from the router (DHCP). You should try powering everything off. Then, in this order, power on your modem, wait 30 seconds, then, power on your router, wait 30 seconds, then power on your computers...This should fix the problem since one computer is working already.

Mar 22, 2009 | D-Link DI-604 4-Port Cable/DSL Router...

1 Answer

I am trying to connect my D-Link router to my PC. I changed providers from DSL to CAble, and now it doesn't work. When I try to hook up the router to the cable modem, I no longer have internet service....

First, you have to directly attach to the cable modem whichever computer the instal tech used to establish your account. Make sure that connection works. Then re-insert the router and clone the MAC address of the instal computer to the router. Then check your DHCP settings. Make sure it's set to get a new IP from your new provider. You may then have to then release your IP and resubscribe.

Feb 19, 2009 | D-Link DI-604 4-Port Cable/DSL Router...

1 Answer

Static Ip with Speedstream 4200 Modem

I am assuming here with the way you have it set up your getting an internet connection.
what you saying i understsand mostly so i'll see if i can help you
first of all you have speedstreem modem that connects to you isp, this is assign your internet address from the isp if you paid for a static IP it would be in here, if not it's assiged by a dhcp from your isp company so if you if turn it off or have a power loss for anymore than 5-15min your ip changes.
now your modem then connects into your belkin router this as well as your modem it's prob set up as dhcp so it wants to issue each computer with an internal address of 192.168.0.X the reason for this is so it knows where to send the incomming information to what computer.
no matter what computer your using the address that goes over the internet will be the one assigned to modem from internet provider so if this need to be static IP to run your game server you will have contact your internet provider for an address.
but you may be confussing the issue a little, my suggestion to you would be:
1. go to your connections on each computer
2. right click on the lan connection choose properties
3. go to internet protocol (TCP/IP) then click properties
4. then click on obtain ip automatically and obtain dns automatically
this will remove the static windows address you may have put in.
try this and see if you can get you game or game server will work.
btw you may have to reboot your computers after this to get be sure to get the new address.

Oct 09, 2008 | Siemens SpeedStream 4200 (13A4200001)...

1 Answer

Can't connect to web configuration

There is a reset known as a 30/30/30 reset. Hold reset with power on for 30secs, unplug power while still holding reset for 30 secs, plug power in while holding reset for 30 seconds more and release, wait 30 secs or more for reboot. This should put it back to factory defaults regardless of brand. Set your IP manually on the PC to be Open your web browser and type in the IP address of the router ( by default). Enter the username (admin) and password (blank by default), and then click Ok or Log In

Aug 26, 2008 | D-Link DI-604 4-Port Cable/DSL Router...

1 Answer

Senao 3220 - access configuration info

I do not know what you have for a DHCP server but some DHCP servers will show you what devices have been given IP addresses which you can use that information to find what address it is at now. Other than that you can use the guess and check method just going through IP addresses until the page comes up, you can use network mapping software to scan your network to find it or you can reset the access point to factory defaults where it will have the default IP address that you can then connect to and re configure it the way you want it.

Jul 06, 2008 | Network Bridges

6 Answers

Placing Sppedstream Modem 4200 in bridge mode ...or if they have the gay firmware >.> go to http://speedstream/brgmode.html then click set your router to log in with your user information with a PPOE login...if your like me and using the dlg-4500 just go to setup and do internet wizard to set up easily...then your ready to go... it can take up to 10 minutes for your router to configure so give it time..and if it doesn't seem like it's working in that time...try cycling your power then check again...and if still not working, do a hard reset (hold reset till lights alternat from green to red) to reset to factor default (do it for your router too becfause it will still be set to sign into your isp for you)

Jun 14, 2008 | Siemens SpeedStream 4200 (13A4200001)...

Not finding what you are looking for?
Network Bridges Logo

Related Topics:

275 people viewed this question

Ask a Question

Usually answered in minutes!

Top Network Bridges Experts

john smith

Level 2 Expert

366 Answers


Level 3 Expert

1061 Answers


Level 3 Expert

3283 Answers

Are you a Network Bridge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides