Question about Proform Perspective Es Treadmill PFTL99806

1 Answer

The incline is stuck in the highest position

I've been trouble shooting steps according to the manual "Press one of the incline buttons and while it is moving remove the safety key. Wait a few seconds and replace the key. It should go all the way up then all the way down to recalibrate." When I did these steps, it would go up about an inch and then go down about the same and stop. It won't go all the way down and recalibrate.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 163 Answers

Try recalibrate. If that dont work, replace the incline motor.

  1. Press speed^ and stop simultaneously
  2. Insert key
  3. Press stop once
  4. Press Incline up
  5. (This should recalibrate incline). If this fails, replace the incline motor.

Posted on Jan 04, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

erpaalai
  • 999 Answers

SOURCE: My Proform treadmill will not incline. It is stuck

Under the hood there should be a tech sheet with calibration instructions. I have not worked on these for several years or I would rattle off the procedure. If the sheet is still there make sure you put it back in the plastic sleeve for next time..... Eric

Posted on Jun 17, 2009

outfield502
  • 79 Answers

SOURCE: the proform 730 CS treadmill is stuck in the

The only way is loosening the screw or nut and making it back manually, but it is the right way to fix it, you should review the KEYPAD, specifically the down key. tries to do the following: turn it off and rub the area where the key now is turn it on again if it does not work with you to replace that part

Posted on Feb 06, 2010

  • 1 Answer

SOURCE: My treadmill will not incline. when you press the

Wondering if you found a solution to this problem yet? I seem to have the same situation with my 730cs treadmill. It is inclined and will not move up or down...thanks.

Posted on Mar 08, 2010

maxtreadmill
  • 832 Answers

SOURCE: the proform 980 turns on but just goes to incline

It is trying to its starting point I would suggest is to unplug the unit open the motor shroud unit. The shroud it has a mini manual this should have a calibration instructions that can be done and also upper electronics self test to see if the processor is functioning properly. It should give a better idea which to head. You can call Icon Fitness@ 1-800999-3756

Posted on May 06, 2010

maxtreadmill
  • 832 Answers

SOURCE: treadmill stuck on highest incline....and motor

If the incline is stuck, it could be a problem as simple as the gearbox on the motor being jammed. Unplug the treadmill remove the motor shroud then remove the incline motor from the treadmill, reconnect the wiring, plug in the treadmill and then try to run the incline motor outside the treadmill. Many times, this will unjam it if that is the problem and then reinstalling it in the treadmill will get it to work. If you have the same problem or it doesn’t run outside the machine and you can hear it try to work, you need to replace the incline motor.
If the incline motor does not move, we need to figure out if the motor is getting voltage. Use a simple multi-meter and set it to AC volts. When you put it into calibration, it tries to calibrate the directions one at a time. Measure across the white and black wires first, then measure across the white and red wires second. If the motor is getting voltage you will read 120VAC (or thereabouts) one one of the measurements. If you have voltage but the motor won't move, you need to replace the motor. . If the incline motor does not move and you have done the voltage test and you do not have any voltage present, there is a problem in the electronics board that supplies the power, you need to replace the board.

Posted on May 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Incline position stuck fully raised.


lube the rack and pinion, and adjust the small POT. see the diagram attached.However RUN the software calibration for easy troubleshooting and fix it. God bless you

The Steps for Newer Style Console Calibration

  1. Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)

  2. Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).

  3. Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.

  4. If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.

  5. Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.

  6. Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.

  7. Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.

  8. Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.

  9. Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."

  10. Press ENTER. You should see "SS" or "55" in the console.

  11. Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.

  12. Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.

  13. When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.

  14. Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.

  15. If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.





3955270e-0ffb-4d9b-b5ae-29087a8d6aec.gif3955270e-0ffb-4d9b-b5ae-29087a8d6aec.gif3955270e-0ffb-4d9b-b5ae-29087a8d6aec.gif3955270e-0ffb-4d9b-b5ae-29087a8d6aec.gif3955270e-0ffb-4d9b-b5ae-29087a8d6aec.gif3955270e-0ffb-4d9b-b5ae-29087a8d6aec.gif3955270e-0ffb-4d9b-b5ae-29087a8d6aec.gif3955270e-0ffb-4d9b-b5ae-29087a8d6aec.gif

Apr 04, 2013 | Exercise & Fitness

1 Answer

Horizon treadmill model ls925t will not allow the grade to be adjusted. It is stuck at the highest grade


RUN THE SOFTWARE CALIBRATION. God bless you

The Steps for Newer Style Console Calibration

  1. Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)

  2. Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).

  3. Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.

  4. If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.

  5. Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.

  6. Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.

  7. Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.

  8. Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.

  9. Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."

  10. Press ENTER. You should see "SS" or "55" in the console.

  11. Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.

  12. Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.

  13. When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.

  14. Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.

  15. If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.



Apr 02, 2013 | Horizon Exercise & Fitness

1 Answer

Nordic Track T5.3 is does not run only inclines to the highest level and back down, what could be the problem?


please RUN the software calibration and fix it
.God bless you

The Steps for Newer Style Console Calibration

1. Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)

2. Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).

3. Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.

4. If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.

5. Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.

6. Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.

7. Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.

8. Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.

9. Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."

10. Press ENTER. You should see "SS" or "55" in the console.

11. Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.

12. Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.

13. When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.

14. Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.

15. If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.

Mar 13, 2013 | Nordic Track Exercise & Fitness

1 Answer

Horizon treadmill won't incline


Step 1:

see the diagram attached.

Clean the motor, lube the gear+shaft
Adjust the small POT for a little.
RUN the software calibration for troubleshooting. see the diagram
2_8_2013_11_10_42_am.gif

Step 2:

2_8_2013_11_11_14_am.jpg

Step 3:

2_8_2013_11_11_47_am.jpg

Step 4:


he Steps for Newer Style Console Calibration
1.Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)
2.Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).
3.Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.
4.If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.
5.Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.
6.Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.
7.Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.
8.Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.
9.Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."
10.Press ENTER. You should see "SS" or "55" in the console.
11.Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.
12.Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.
13.When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.
14.Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.
15.If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.
God bless you

Feb 07, 2013 | Horizon Fitness Horizon T101 9 Program...

1 Answer

How do you calibrate a bladez t-5.9 treadmill


follow the steps and proceed according. God bless you

The Steps for Newer Style Console Calibration
1.Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)
2.Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).
3.Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.
4.If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.
5.Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.
6.Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.
7.Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.
8.Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.
9.Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."
10.Press ENTER. You should see "SS" or "55" in the console.
11.Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.
12.Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.
13.When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.
14.Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.
15.If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.

Jan 14, 2013 | Exercise & Fitness

1 Answer

Tempo 621T treadmill stuck in incline postion scale is reading 0 but it is not completely down..How to reset my incline button


Run the software calibration for troubleshooting and fix it. See the next steps. God bless you

The Steps for Newer Style Console Calibration

  1. Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)

  2. Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).

  3. Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.

  4. If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.

  5. Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.

  6. Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.

  7. Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.

  8. Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.

  9. Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."

  10. Press ENTER. You should see "SS" or "55" in the console.

  11. Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.

  12. Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.

  13. When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.

  14. Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.

  15. If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.
Lube the elevation motor, shaft and gear. adjust the POTentiomer,
1_9_2013_4_31_43_pm.jpg

Jan 09, 2013 | Exercise & Fitness

1 Answer

Treadmill belt runs too fast and will not power off with control panel


Step 1:

test the speed sensor,m for open or faulty, clean it, and tight the connector. see the diagram attached.
However follow the steps for RUN the.s calibration for fix it.
God bless you
1_7_2013_11_03_18_pm.gif

Step 2:

The Steps for Newer Style Console Calibration:
  1. Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)
  2. Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).
  3. Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.
  4. If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.
  5. Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.
  6. Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.
  7. Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.
  8. Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.
  9. Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."
  10. Press ENTER. You should see "SS" or "55" in the console.
  11. Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.
  12. Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.
  13. When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.
  14. Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.
  15. If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.

Jan 07, 2013 | Exercise & Fitness

1 Answer

HOW TO RECALIBRATE AT BLADEZ POWERMILL 6525


please proceed according . Happy new year. God bless you

The Steps for Newer Style Console Calibration:

  1. Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)

  2. Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).

  3. Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.

  4. If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.

  5. Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.

  6. Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.

  7. Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.

  8. Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.

  9. Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."

  10. Press ENTER. You should see "SS" or "55" in the console.

  11. Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.

  12. Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.

  13. When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.

  14. Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.

  15. If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.

Jan 01, 2013 | Dmm Vision Fitness T9500 Treadmill

1 Answer

My treadmill is stuck at the highest incline and will not decline


Although it is fairly rare the incline motor can jam up into the highest position and get stuck there. To fix this take off the plastic hood that covers the incline motor and depending on the motor you should be able to wind it with your hand out of the highest position. When it is out of the highest position run the calibration as described in the owner's manual and it should go all the way up and all the way down. If it is not this type of motor that can be wound by hand then the first and last thing to do is to try calibration of the incline as described in your manual. If this does not work then a new incline motor is needed.

Dec 31, 2009 | Proform Quick Burn Pro Treadmill with 12...

5 Answers

Treadmill incline stuck @ steepest level (highest)


MAKE SURE YOU STAND TO THE SIDE OF THE TREADMILL WHILE PERFORMING THIS
1)Connect the wall power to the treadmill
2)Remove the safety key
3)Hold down the red stop button and red increase speed button (this is the red triangle next to the start button)
4)Insert the safety key while holding both buttons down in step3
5)The treadmill will now go into a diagnotstic calibration mode
6)Let go of both buttons in step 3 and press the oval stop button once
7) Now press the up arrow green incline button once(This is located to the left of the yellow program button)
8) Allow the treadmill to go through a calibration cycle, once it completes and stops moving remove the safety key count to 3 and reinsert.

Jan 08, 2009 | Exercise & Fitness

Not finding what you are looking for?

Open Questions:

See all Proform Perspective Es Treadmill PFTL99806 Questions

Proform Perspective Es Treadmill PFTL99806 Logo

244 people viewed this question

Ask a Question

Usually answered in minutes!

Top Proform Exercise & Fitness Experts

Matt Olenzek
Matt Olenzek

Level 2 Expert

293 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Owen Barnes

Level 3 Expert

867 Answers

Are you a Proform Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...