Question about Yakima Skybox Pro Cargo Box

Open Question

Skybox stuck closed - Yakima Skybox Pro Cargo Box

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I tune my TV in the kitchen to my Sky box in another room.


Sky box stuck in Stand By on red light Sky Box Guides faq

Sky Troubleshooting faq

either you have it hooked up wrong or skybox doesnt allow 2 screen use,you may need another skybox

May 14, 2015 | Televison & Video

2 Answers

Skybox beverage dispenser. will dispense one can


I had the same problem. Found the cover where the beverages dispense to be rusted and not resetting. After the can dispenses, just push the cover back into position and this should help.

Jun 09, 2009 | Maytag SkyBox MBV1976A Beverage Dispenser

1 Answer

Maytag skybox 1976AAB wont dispence


I had the same problem. The hinge pin on the dispensing door was rusted and this kept the door from closing completly. The door sensor magnet was not making contact with the door sensor and this caused the error. I removed the pin, sanded it down and it before reinstalling. It works fine now.

Apr 05, 2009 | Maytag SkyBox MBV1976A Beverage Dispenser

1 Answer

Hi my skybox stop cooling


The SkyBox operates with two individual systems. The dispenser assembly, the LED indicators and the circulating fan operate on a low voltage circuit. The circulating fan runs anytime the SkyBox is plugged in.

The cooling system operates on 120vac. The cold control inside the beverage compartment is an on demand switch that sends 120vac to the compressor when cooling is needed. There are no parts available for the compressor, so if it determined that power is reaching the compressor, the windings are ok, a 3 in1 hard start kit (Supco URCO210) can be installed by a qualified service technician.

Mar 16, 2009 | Maytag SkyBox MBV1976A Beverage Dispenser

1 Answer

Jamming dispencer for my skybox maytag.


You may not have a dispenser problem at all, but rather a build up of frost and ice. The evaporator is embedded in the interior wall directly behind the two middle dispensers. The dispenser effected most bt the ice build up is the second one from the bottom. Unplug the unit and leave the door open for 24 hours. Then plug it back in, reset your thermostat at the 11:00 position and close the door. If the problem is still present, the next step would be to remove the dispenser assembly and search carefully for a disc shaped magnet about the size og the leter "O" on your keyboard. There are 9 of these magnets in the SkyBox. The dispensing cylinder has one built in, as does the flap at the end of the dispensing row. When the cylinder moves to dispense a beverage, a reed switch detects the magnet. Next it looks for that flap at the end to open when the beverage falls down. Finally, as the beverage comes out in the door another reed switch detects the opening and closing of the flapper door. If the board does not see the signal from any of the reed switches, it assumes there is a product stuck someplace.
I hope this helps.

Feb 25, 2009 | Maytag SkyBox MBV1976A Beverage Dispenser

1 Answer

Maytag Skybox stays at 50 degrees all the time


The SkyBox was built for Maytag by a company in China. Production stoppedabout 2 1/2 years ago, and Maytag purchased ALL available service parts available at that time. As inventories are depleted, there will be no more parts available.
An issue with the SkyBox involved a build up of frost and ice on the evaporator plate built into the wall behind the dispensor assembly. This build up insulated the product from the evaporator coil. It also caused the circulation fan to stop running. Unplug the unit and leave the door open for 24 hours. Plug it back in, set the thermostat indicator at the 11:00 position and close the door. See if this brings the temps back down to the 36 to 42 degree range, I hope this helps.

Jan 26, 2009 | Maytag SkyBox MBV1976A Beverage Dispenser

4 Answers

Maytag SkyBox


For the soda name tags, I pulled logos off the internet and printed them the correct size on 20-pound paper. Different paper gives different translucence, so you might have to experiment to get the right amount of light coming through.
PS: thanks for the part no. on the relay

Apr 21, 2008 | Maytag SkyBox MBV1976A Beverage Dispenser

1 Answer

Maytag Skybox


Looks like I found the answer to the problem of Skybox not dispensing. I replaced the sensor in the dispensing door and my Skybox now works great!
Part is available from partselect.com just look up your Skybox model number, mine was Skybox model MBV1976AAB. The diagram on the website should show you the exploded view of the door section of your Skybox. You are looking for partselect.com part number 901892 or on the exploded view it will be number 21. The Maytag part number is 11001182, board flipper sensor. My Skybox had been down for two years and now works again!

Mar 27, 2008 | Maytag SkyBox MBV1976A Beverage Dispenser

11 Answers

Skybox won't dispense anything


check the door where the cans come out. there is a sensor or the left side. if it is too far away from the door or if it's broken, it will do exactly what you said. i read somewhere that you can adjust the sensor closer to the door. i just bought one of the last one of these on the shelves 2 days ago and mine won't cool at all. stupid maytag..

Mar 01, 2007 | Maytag SkyBox MBV1976A Beverage Dispenser

Not finding what you are looking for?
Yakima Skybox Pro Cargo Box Logo

Related Topics:

307 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yakima Winter Sports Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75097 Answers

Todd Arndt
Todd Arndt

Level 3 Expert

2044 Answers

Are you a Yakima Winter Sport Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...