Question about Mitsubishi WD-62725 62" Rear Projection HDTV-Ready Television

2 Answers

No picture after replacing lamp

Replaced lamp, plugged in now green powerlight flashing. No manuel to find out how to reset lamp timer

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Unplugged tv, pulled the lamp back out, vaccuumed out inside of tv, replaced lamp and plugged back into outlet. Power light flashed green for approximately two minutes then went out. Turned tv on, and all is right with the world once again. Had to look at an online manuel to figure out what it might be.
Thanks for following up.
Darryl

Posted on May 20, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 179 Answers

The chassis needs to be rebuilt. go to www. tv-techs.com for more info

Posted on May 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a sony kdf-e42a10 that will work for about 2 or 3 miutes at a time then losesound and picture for about a minute. green powerlight will flash while not working.


Hello, the lamp is going bad, use only a genuine Sony lamp in that set to keep from damaging the ballast. the part # is XL-2200U....tks

Aug 02, 2014 | Sony XL2400 LAMP - TV KDF-E42A10,...

1 Answer

We replaced the lamp about 6 months ago..but now it cuts off randomly..the red light and one green light will flash? Lamp replacement was when all 3 lights were flashing. Suggestion?


Is the picture quality good if it is then the lamp is ok try to reset the lamp timer if you haven't all ready. I think that the problem is coming from the ballast board this is the power source to the lamp, with time this part starts to ware out and starts to get weak. that is the reason your lamp does not stay on

Sep 07, 2010 | Samsung HL-S5686W 56" HDTV

1 Answer

Green Light Flashing For Lamp That I Just Replaced


lamp timer may need to be reset, or lamp door may be open. unplug tv for 1 minute, plug in and wait 30 seconds before powering on. make sure lamp is all the way in and door closed before you plug it in. if it keeps erroring, check the manual and see what the error code indicates

May 21, 2010 | Zenith Z52SZ80 TV

1 Answer

Replaced bulb,still not turning on-power flashes green then red and lamp light comes on


Did you reset the lamp timer? If you replace the lamp and dont reset the lamp timer the TV will continue to display the lamp error until you do.

Sep 22, 2009 | Panasonic PT-50LC13 50" Rear Projection...

2 Answers

Timer light did not stop flash


Lamp is not the issue. It most likely is a your DM card. You most likely have some capacitors that need to be replaced. This is a terrible issue with this unit. Do a google search for "DM" and the model number and you should see hundreds of posts.

Jul 02, 2009 | Mitsubishi WD-62525 62" Rear Projection...

2 Answers

Lamp indicator flashes three times even with new lamp.


Check your manuel for Lamp counter reset facility , lamps sometimes will not retsrat untill this is done ... Regards Vortash

May 05, 2009 | Office Equipment & Supplies

1 Answer

I have a sansung dlp model#HLS4676SX Lost picture and sound


Replace Lamp if you have your manuel book that came with TV it will Tell you how and what to do if it is Lamp. Acme Parts has replacement lamps call 1-800-575-9833 or go to website acme-sales.net.

Jan 07, 2009 | Televison & Video

1 Answer

WD-62525 green timer light keeps blinking after lamp replacement


Did you let the green light flash for about 70 seconds? It goes thru a self check when plugged in and takes a little time

Dec 29, 2008 | Mitsubishi WD-62525 62" Rear Projection...

1 Answer

Green color


reset all color settings from the unit's menu.
disconnect any source and turn off the unit
turn on the unit and wait for the manufacturers logo to show up (and it must be BLUE).

not blue ? reseat the lamp. replace lamp if it doesn't work.

Nov 21, 2008 | Epson Powerlight 8300NL Multimedia...

Not finding what you are looking for?
Mitsubishi WD-62725 62" Rear Projection HDTV-Ready Television Logo

204 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1210 Answers

The Knight
The Knight

Level 3 Expert

74136 Answers

Jaime Hernandez

Level 3 Expert

2318 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...