Question about Office Equipment & Supplies

Open Question

Oki B431dn error message 563 - Office Equipment & Supplies

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
pineworks
  • 4041 Answers

SOURCE: OKI C8600 Replace Image Drum - 563: K Drum Life

Solution:

  • Power on printer while holding both the + & - buttons simultaneously; release when “OKIUSER” is displayed.
  • Press either the + or – button until “ENGINE DIAG MODE” is displayed; press the Enter button and “DIAGNOSTIC MODE xx.xx.xx” will be displayed.
  • Press and hold both the - & On-line buttons simultaneously until “ENG DIAG LEVEL2” is displayed.
  • Press either the + or – button until “CONSUMABLE COUNTER SET” is displayed, press the Enter button; you are now in the menu to set various consumables.
  • Press either the + or – buttons to scroll through the various consumables, at the desired consumable press the Enter button and the last digit of the count will start flashing.
  • Press the Cancel button to decrease the digit amount or press the On-line button to increase the digit amount; press the + or – buttons to move along individual digits in the count.
  • Once the count is at the level you desire, press and hold the On-line, Cancel, & Back buttons simultaneously until the “*” reappears next to the count; consumable’s count are reseted to the number you specified.
  • Press the + or – buttons to move to the next consumable and repeat at step 5.
  • Once all consumable counts have been set to desired amounts that are below their end-of-life thresholds, you can use the Back, +, & - buttons to exit through the menus
  • until “INITIALIZING” is displayed.

Posted on Jan 30, 2010

Ad
  • 72 Answers

SOURCE: ned drive printer oki B431dn

You should be able to find what you need here. Select your operating system on that computer and click on the right file.

Posted on Apr 11, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a problem with my printer oki b431dn error code is 382 "paper jammed" but no one paper into ther printer cause i diassembly printer and build it back but same problem...what can i do with it?


Open the rear cover and in the centre of the curved black guide you will see a small black lever with a silver spring on it. this is a arm to the jam sensor. check it moves freely and returns to its upright position. If ok the blow air under it into the actual sensor. Check the pickup roller is not smooth. If it is its rubber tyre can be rotated so the good part touches the paper.

Oct 28, 2017 | OKI Office Equipment & Supplies

1 Answer

Oki C5350 error 563


563 I usually drum code reset, some OKI machine have sensors in the side frames they look like a little round window, clean with Q tip, I will assume you have replaced the drum, right?

May 05, 2014 | OKI C5510 MFP All-In-One Led Printer

1 Answer

Oki b431 service 134


It may be necessary to replace the LED head. Part number 44317201

Apr 03, 2014 | Oki Electric Industry B431dn Printer

1 Answer

Oki b411dn error 563


The image drum cartridge has reached the end of
its life. Replace the image drum cartridge

Jan 12, 2014 | Oki Electric Industry B411d Printer

1 Answer

Error message


If looking into the paper feed there is no visible jamb, check the outside of the printer elsewhere. There is usually an access panel that comes off to manually remove any caught paper from behind where your paper loads to copy.

Sep 19, 2013 | Oki Electric Industry B431dn Printer

1 Answer

I get a timeout message at the end of a print run


Toggle through the menus on the printer to the "Sys Config Menu" and turn OFF both the "Manual Timeout" and "Timeout in Job".

As a note, we only have this issue crop up when our printer is accessed through an Apple Time Capsule. When it was directly attached to the computer, or accessed directly through IPP we had never had the error page print.

Jun 03, 2012 | Oki Electric Industry B431dn Printer

1 Answer

Ned drive printer oki B431dn


You should be able to find what you need here. Select your operating system on that computer and click on the right file.

Apr 11, 2011 | Computers & Internet

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Office Equipment & Supplies Experts

k24674

Level 3 Expert

8073 Answers

jasbo
jasbo

Level 3 Expert

2237 Answers

yadayada
yadayada

Level 3 Expert

80339 Answers

Are you an Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...