Question about Office Equipment & Supplies

Open Question

Monarch 1131 prices print too low on label. tried reloading several times.

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: I am trying to load

How do you load lable roll into the Monarch paxar 1131?

Posted on Aug 04, 2008

  • 226 Answers

SOURCE: How do I load tape in a Monarch PAXAR 1131?

* Step 1 Pull the latches back and open the cover until you hear a click.

  • Step 2 Tear off the first ten inches of the labels and liner.
  • Step 3 Place the label roll between the holders.
  • Step 4 Drape the supply across the labeler and position it in the center over the peel bar.
  • Step 5 Close the cover.
  • Step 6 Hold the trigger down while holding the labeler upside down.
  • Step 7 Feed label strip over the roller and into the large slot under the arrows.
  • Step 8 Hold the strip in place and squeeze the trigger eight times, until the labels feed through the rear exit.
  • Step 9 Remove and discard any loose labels.
  • Posted on Jul 20, 2009

    • 3 Answers

    SOURCE: My Dymo Labelwriter 450 turbo feeds out 4 labels

    Multiple label feeding usually occurs because the sides of the spool holding the roll are not squeezed tightly together. Make sure there's no gap between the labels and the sides of the spool. If this doesn't help. take out the labels and blow a blast of air into the feed slot. There is a sensor inside the slot on the left that detects the hole in the labels, and maybe it is blocked.

    Posted on Jan 26, 2011

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    Reloading pricing tape in gun?


    price gun should have a diagram on how to reload it, look to find a squeeze release clip on one of the ends or bottom. u will have to remove 5 to 10 stickers so it does not jam.

    Apr 12, 2011 | Monarch Marking Pricemarker Labeler, 2...

    1 Answer

    Monarch paxar 1110 pricing gun brand new. The box was thrown away and it isn't working. The label prints out without a price the ink is fine we tried it on a different gun. Any trouble shooting ideas??


    Here's a video that shows how to properly load supplies into the gun. It's possible that the supplies aren't loaded properly..

    http://www.racoindustries.com/monarch-1130-1131-1136-labeler-loading-video.htm

    Dec 27, 2010 | Paxar Monarch 9825 Thermal Label Printer

    2 Answers

    How do i replace the ink roller in a monarch 1131 price gun


    To replace the ink cartridge, turn the latch on the right side of the gun to an upright position. Pull the door out. The ink roller is on the end of the door in a plastic holder. Push the holder apart slightly to remove the old ink roller and insert a new one. Replace the door and turn the latch to hold it in place.

    Nov 15, 2010 | Monarch Pricemarker Kits

    1 Answer

    Ok this stupid paxar 1131 gun is a pain in the ***, is there a video to show how to load this gun?


    Here's a video on how to properly load gun...

    http://www.racoindustries.com/monarch-1130-1131-1136-labeler-loading-video.htm

    Sep 02, 2010 | Paxar Monarch 9403 Thermal Printer

    1 Answer

    Monarch 9825 Thermal Label Printer: my monarch 115 pricing gun, the numbers reels gett...


    You may wish to have Avery Dennison, the folks that purchased Monarch/Paxar, to service your printer.

    Their phone number is 1-800-543-6650 and ask them the correct address for service. Your bands may be getting too loose, and need to be replaced. If it is something that they can instruct you to take care of, they can sell you the bands and provide instruction.

    May 06, 2010 | Paxar Monarch 9825 Thermal Label Printer

    2 Answers

    Where can you get parts for a Monarch 1110 label gun?


    Monarch label gun replacement parts can be easily found on amazon, click here Amazon com Monarch 1110 label gun parts and take a look. Wish you best of luck.
    Martin

    Apr 18, 2010 | Paxar Monarch 9825 Thermal Label Printer

    1 Answer

    The sticker does not come out all the way. I've taken it out & reloaded but the price sticker will not come all the way out


    It is possible that you are loading the wrong type of label for this printer. Since these printers use either a die cut gap or black mark on the back of the label liner to know when to stop, it is possible that the labels you are using are not meant for this printer.

    If you have used them before, you may have to change a setting in your menu from die cut to black mark or visa versa. Then you should see your labels dispense to the proper position when indexing or printing.

    Sep 30, 2009 | Paxar Monarch 9403 Thermal Printer

    2 Answers

    How do I load tape in a Monarch PAXAR 1131? The machine was turned over to me, but the instruction manual is missing?


    * Step 1 Pull the latches back and open the cover until you hear a click.
  • Step 2 Tear off the first ten inches of the labels and liner.
  • Step 3 Place the label roll between the holders.
  • Step 4 Drape the supply across the labeler and position it in the center over the peel bar.
  • Step 5 Close the cover.
  • Step 6 Hold the trigger down while holding the labeler upside down.
  • Step 7 Feed label strip over the roller and into the large slot under the arrows.
  • Step 8 Hold the strip in place and squeeze the trigger eight times, until the labels feed through the rear exit.
  • Step 9 Remove and discard any loose labels.
  • Jul 20, 2009 | Paxar Monarch 9403 Thermal Printer

    1 Answer

    Problem to print label when Monarch is installed on network


    101 : The format referenced by batch isn't in memory. (Try rebooting printer or closing/opening software)
    005: Supply width is invalid. (Check your format data)

    May 29, 2009 | Monarch 9855 Thermal Printer

    Not finding what you are looking for?
    Office Equipment & Supplies Logo

    Related Topics:

    28 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Office Equipment & Supplies Experts

    kakima

    Level 3 Expert

    102366 Answers

    k24674

    Level 3 Expert

    7993 Answers

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    Are you an Office Equipment and Supply Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...