Question about Amana LWA90A

Open Question

What is error code bp on Amana washer model lwa90aw?

I am getting error code BP on a washer model lwa90aw. What is the cause of this error?

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Fault code on an Amana Washer

The door is open. Be sure that the door is completely closed.

Posted on Mar 01, 2009

Ad
  • 2 Answers

SOURCE: what does error code 6P mean on an Amana washer model LW9203W2B

SH: Open thermistor. Unplug appliance and let rest for 15-30 minutes, then plug back in. If code continues, unplug appliance and call for service.

bP: Pressure switch error sensed. Washer will not operate when this error is displayed. Check for pinches or kinks in the water inlet hoses and straighten if necessary. Check the water inlet hoses filter screens and clean if needed. Verify that the water supply is turned on. Unplug washer and let rest for 15-30 minutes, then plug back in. If code continues, call for service.

rP: Water supply problem in spin cycle. Check for pinches or kinks in the water inlet hoses and straighten if necessary. Check the water inlet hoses filter screens and clean if needed. Verify that the water supply is turned on. Unplug washer and let rest for 15-30 minutes, then plug back in. If code continues, call for service.

LO: Lock Out mode. To activate, press START and STOP/OFF pads at the same time. To deactivate, repeat the procedure.

AU: Flashes when a factory preset cycle is put on hold. A normal function.

Clean Filter: Flashes when a cycle is selected as a reminder to clean the filter before starting a cycle for optimum drying results. Code clears when the door is closed and the START pad is pressed.

Posted on Sep 01, 2010

tbirdfan1
  • 3051 Answers

SOURCE: amana front load washer error code "nd". Door is

Hello there and welcome to fixya
From what you're describing it sounds like the drain pump is blocked. The nd error code indicates "no drain". If the unit can't drain it won't spin. You're going to have to slide the washer out far enough to remove the rear panel; be careful not to damage the floor. Once you get the rear panel off you will see the pump. Be sure to have plenty of towels & a small container to catch water. I am sending you instructions from the service manual to remove and replace the pump. Another possibility is the drain line is blocked or something is stuck in the tub to pump hose.

Posted on Nov 05, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Amana washer model lwa90aw how many microfarads in capacitor


It should be printed on the side of the capacitor but there are other ratings on it to consider as well,also the pin positions.

Nov 13, 2013 | Amana Washing Machines

1 Answer

What does the error code "OP" mean?


OP - Open Thermistor - Replace thermistor.

Aug 27, 2013 | Washing Machines

1 Answer

SOFTWARE PROBLEM DURING PUMP FUNCNTION SO MANY ERROR I WANT UREGENT SERVICE PLESE CONTACT NO. & ADD. SERVICE CENTER IN AHMEDABAD


What brand of BP Monitor?

Is this a personal BP monitor?
Or is it a hospital BP monitor?

Well.. you have to check the cuff to see if it's OK. Most of the errors are because of the cuff which has a balloon inside the cuff.

It depends on your model.

On some models you can take off the cuff line. Check if there is air coming out from the BP machine. If there ir air, it must be probably the cuff.

If both the cuff and machine is OK, then the problem must be the machine calibration.

Is it electronic or manual BP?

Hope it helped.

God Bless You!

Feb 05, 2011 | Health & Beauty

1 Answer

I keep getting low readings. I had my bp read by a nurse yesterday it was 191/110 and today it was 196/119. The bp monitor model BA-616W 138/82. Please advise me?


you should already be dead if your bp is 196/119.normal runs 120/80.hypertension starts at 140/90. wrist bp units are often incorrect. dump nurse and cuff. go see your doc or use the free units at kroger

Oct 07, 2010 | Walgreens Health & Beauty

2 Answers

Not charging video will not eject


CANON MV630I battery Specs:


  • Cell Type : LI-ION
  • Volts : 7.4V(Compatible with 7.2V)
  • Capacity : 4400mAh
  • Average Run Time :2-4 hours(minimum)
  • Color : GREY
  • Dimension : 55.10x38.20x39.90mm
  • Net Weight : 146.00g
  • Cpmpatible Model:
  • canon 5797a007, canon 5797a010, canon bp-508, canon bp-511, canon bp-511a, canon bp-514, canon bp-522, canon bp-535, canon pc511, canon vcn009, canon vcn009s, cta db-bp522, delkin dd/bp522, duracell drc522, empire bli-193-2.4, energizer er-c600, gp vcl008, hahnel hl-522, hama 46810, hama cp-810, optex li36, polaroid pr-522l, rayovac rv5462, sakar bp-522cl, sunpak hl-522s, techcell l522us, vivanco bp-22672decf09.jpg

    Jul 22, 2010 | Canon MV630i Mini DV Digital Camcorder

    1 Answer

    Centrios wrist BP monitor, model 10A03. When pu...


    centrios wrist monitor works to inflate and deflate monitor but displays "1" instead of blood pressure reading

    May 21, 2010 | Health & Beauty

    1 Answer

    What does error code 6P mean on an Amana washer model LW9203W2B


    SH: Open thermistor. Unplug appliance and let rest for 15-30 minutes, then plug back in. If code continues, unplug appliance and call for service.

    bP: Pressure switch error sensed. Washer will not operate when this error is displayed. Check for pinches or kinks in the water inlet hoses and straighten if necessary. Check the water inlet hoses filter screens and clean if needed. Verify that the water supply is turned on. Unplug washer and let rest for 15-30 minutes, then plug back in. If code continues, call for service.

    rP: Water supply problem in spin cycle. Check for pinches or kinks in the water inlet hoses and straighten if necessary. Check the water inlet hoses filter screens and clean if needed. Verify that the water supply is turned on. Unplug washer and let rest for 15-30 minutes, then plug back in. If code continues, call for service.

    LO: Lock Out mode. To activate, press START and STOP/OFF pads at the same time. To deactivate, repeat the procedure.

    AU: Flashes when a factory preset cycle is put on hold. A normal function.

    Clean Filter: Flashes when a cycle is selected as a reminder to clean the filter before starting a cycle for optimum drying results. Code clears when the door is closed and the START pad is pressed.

    Dec 29, 2009 | Amana Washing Machines

    Not finding what you are looking for?
    Washing Machines Logo

    Related Topics:

    346 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Amana Washing Machines Experts

    Dan Webster
    Dan Webster

    Level 3 Expert

    8220 Answers

    Sal DeAngelo

    Level 3 Expert

    2180 Answers

    Terry Schneider

    Level 2 Expert

    177 Answers

    Are you an Amana Washing Machine Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...