Question about Exercise & Fitness

1 Answer

Treadclimber nautilus tc916

I have a nautilus Tc 916 tredclimber. when power on a display showing DRV RESET 1 only. what will i do sir

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 161 Answers

You may have a blown fuse. Check fuse box

Posted on Jan 04, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

rockfixya
  • 679 Answers

SOURCE: Bowflex Treadclimber tc 1000 turns off

Hi,
Problem could be low colant, water pump, fan not kicking on (bad sen or bad fan motor) radiator dirty,
so the Treadclimber not working properly.
I hope this helps u
Thanks for using FixYa.

Posted on Jan 30, 2009

  • 1 Answer

SOURCE: bowflex tc 1000 treadclimber

TC1000 from Bowflex, works okay for 15 mins then the speed surges ahead and stops dead with error E1

Posted on Jan 12, 2010

maxtreadmill
  • 832 Answers

SOURCE: Bowflex TC 1000 treadclimber causing power surges

You are not on a dedicated circuit the amp draw must be significant thus pulling down the voltage causing your grief. Find a and outlet that is not on the same circuit your electronic units maybe in another part of the house. Or put in a new circuit if you have a vacant in the breaker box, but that need a qualified electricians to do the job$$$$$

Posted on Jul 19, 2010

ercupa190
  • 12223 Answers

SOURCE: I have a nautilus tc916, as soon as i turn on poer

Dear Sir:
The VSD, is installed in a bracket located side of the treadmill.

P6-P7= 115VCA
P8-V6=230 VAC

Be carefully you must do this with testing Dvom o Vom. That is you do not any schematic for to do this.

sincerely.

E.CUADRA

Posted on Nov 04, 2011

  • 1 Answer

SOURCE: my bowflex treadclimber tc 20 is putting out error codes H03,H13,H24 whats wrong

I have the exact problem. My machine is 3 days old. I am also getting this H03, H13, H24 error. I called the 1-800 number for the Treadclimber TC20 and they informed me that a handful of machines were sent out with a bad control board. I am waiting for a replacement board.

Posted on May 08, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The power will not come on when plugged into a working outlet


[PDF]Bowflex Treadclimber - Nautilus

download.nautilus.com/.../Bowflex/BFX_TC5300_6000_OM_AM_Rev...
Bowflex® TreadCl mber® Assembly and Owner's Manual. PREFACE ..... will not workand an electric shock hazard may be present if the wires ..... Plug the machine into anoutlet and turn on the power (see Page 24: Turning on the Power). 2.

Nov 04, 2015 | Bowflex TreadClimber TC20

1 Answer

E5-5 error code on Treadclimbe


follow the steps and fix it. God bless you
The power up test sequence has detected a key in the operated condition. The power up test
sequence is performed every time the unit is turned on (powered up). This test is performed
because a permanently stuck key will inhibit the correct operation of the unit.
Possible Causes
1. A key on the display housing is permanently stuck in the operated condition.
2. One of the upper PCA's keypad interface chips has failed.
3. Liquid (perhaps perspiration) is present on the surface of a touch sensitive display.
Possible Remedies
1. Remove the keypad connector cable from the upper PCA. Restart the power up sequence, if
the ERROR 5 is no longer present, the keypad is the cause. The keypad is typically part of
the display housing. Replace the display housing to correct the problem.
2. Remove the keypad connector cable from the upper PCA. Restart the power up sequence, if
the ERROR 5 is still present, the upper PCA is the cause. Replace the upper PCA to correctc3d2efcd-4214-4aa4-b3ad-6b1e2ccdbf44.gif

Jun 20, 2013 | Exercise & Fitness

1 Answer

Tm com error 1


adjust the Speed sensor, test for open or faulty, clean it, tight the plug or connector very well. see the diagram attached.
2) Test the input voltage motor, if there are the motor need repair, see my personal TIPS for motor help.
3) test the output voltage board, for input voltage motor, if there are NOT the board is faulty.
God bless you
12_13_2012_4_07_18_pm.gif

Dec 13, 2012 | Nautilus Tc916 Treadclimber- Refurbished

1 Answer

My bowflex treadclimber tc 20 is putting out error codes H03,H13,H24 whats wrong


I have the exact problem. My machine is 3 days old. I am also getting this H03, H13, H24 error. I called the 1-800 number for the Treadclimber TC20 and they informed me that a handful of machines were sent out with a bad control board. I am waiting for a replacement board.

Apr 14, 2012 | Bowflex Treadclimber

1 Answer

Treadclimber centering


Dear Sir:
ecalibrate the machine if speed is not registering, belts stop turning or the display readout shows an "err, LS, OS" on the face. Calibrate the TreadClimber by plugging it in. Stand on the foot platforms, or floor mat. Do not stand on the walking belt. Insert the safety key. Press the "start" key when "CAL/PRSS/STRT" shows on the readout. If readout fails to show the "CAL/PRSS/STRT" symbol, turn off machine and turn it back on. Press "ENTER" and then "DOWN SPEED" at the same time until "CAL/PRSS/STRT" shows up on the display. Belts will start and stop during the calibration; do not be alarmed. Do not make any adjustments or interrupt the display of numbers as the unit goes through the calibrations. When the machine is finished calibrating, the readout will display "CAL...PASS" and you can press the "POWER" key to get out of the calibration section.

sincerely. God bless you.

ernesto cuadra
managua, nicaragua. c.a

Feb 15, 2012 | Exercise & Fitness

1 Answer

I have a nautilus tc916, as soon as i turn on poer the vsd board frys at p23 on the board, was wondering if anyone actually has illustrations of how the board looks wired for 110 volts, and also if anyone...


Dear Sir:
The VSD, is installed in a bracket located side of the treadmill.

P6-P7= 115VCA
P8-V6=230 VAC

Be carefully you must do this with testing Dvom o Vom. That is you do not any schematic for to do this.

sincerely.

E.CUADRA

Nov 02, 2011 | Nautilus Tc 916 Treadmill Vsd Board

1 Answer

T914 "drive motor error 2"


1)VSD(variable speed drive) MICROPROCESSOR eprom/sram failure: Exchange VSD board.
2) Belt speed pickup,failure in the speed pickug, to due motor, wiring or controller board.

sincerely.

E.CUADRA

Sep 12, 2011 | Nautilus Tc 916 Treadmill Vsd Board

1 Answer

My bowflex is showing "err l5" what is wrong with it?


This error indicate that the console is unable to deter mine the speed of the belts. Potential parts associated with this are the Speed Sensor, MCB, Motor, I/O cables, and Upper Electronics. Call Nautilus Service Dept 1-800-628-8458

Apr 14, 2010 | Bowflex Treadclimber

4 Answers

Error Code E1


I had the same error message E1 at 10 seconds according to the LCD display on an older Treadclimber TC1000. I called Bowflex 1-800-792-6784 and first thing they told me was to check the drive sensor on the back left corner of machine. It is two wires connected by 2 white connectors that snap together. The end of the sensor has a rubber cap that is supposed to be approximately 1/8 inch from the drive pulley. The rubber cap plugs into a small hole within the "firewall" of the drive pulley, but the end of the cap does not actually touch anything. They can email you a picture of it. If it ever gets knocked loose, the machine will register this e1 error, in some cases- hope this helps.getattachment.aspx&hm__qs=file%3d3d2f2ee0-2668-46ea-b32c-db049d56cb37.jpg%26ct%3daw1hz2uvanblzw_3d_3d%26name%3daw1hz2uwmdiuanbn%26inline%3d1%26rfc%3d0%26empty%3dfalse%26imgsrc%3dcid%253aimage002.jpg%254001c99c08.13bd6320&oneredir=1&ip=10.12.128.8&d=d6608&mf=0&a=01_0b590aaade5e800af268d347750ab151eca93264be20cd9ce2166e583b18cfe9

Jan 24, 2009 | Bowflex Treadclimber

Not finding what you are looking for?
Exercise & Fitness Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Exercise & Fitness Experts

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Sportsmith LLC
Sportsmith LLC

Level 3 Expert

914 Answers

Tom Chichester

Level 3 Expert

33272 Answers

Are you an Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...