Question about ASUS P5KPL-VM Motherboard

Open Question

I need a block schematic diagram please -

None of the four IDE drives and the floppy drive are recognised by the BIOS. I'm trying to decide whether this fault is caused by the collapse of one of the ALi chips; and if so, whether this board is now scrap. I need the block schematic to find out what the drives are connected to.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6 Answers

SOURCE: ASUS KBN-E MOTHER BOARD 754 processor 512mb ram

Try plugging the drives into another computer to see if they actually work, ie read discs etc if they do then try swapping the power supply out of your computer.. if this doesn't work then I would say your motherboard is dead. Good luck

Posted on Jun 03, 2007

SOURCE: Asus P5K-E Wifi/AP configuring sata as raid

I have 3 hard drives, one I have my windows system files on, and on the others I was planning on doing a mirrored raid. Is this possible? I couldn't get it to work, I put the hard drive mode into RAID mode or ACPI (or whatever the other mode was) and it doesn't allow me to boot into windows or anything, blue screen of death.
Only works in IDE mode, but I cant make it raid using IDE mode :"(

Posted on Jun 05, 2008

  • 1 Answer

SOURCE: how to install window XP without floppy disk on asus P5RD1-VM

@font-face { font-family: Cambria Math; } @font-face { font-family: Calibri; } @font-face { font-family: Tahoma; } @font-face { font-family: Segoe UI; } @page Section1 {size: 8.5in 11.0in; margin: 1.0in 1.0in 1.0in 1.0in; } P.MsoNormal { FONT-SIZE: 12pt; MARGIN: 0in 0in 0pt; FONT-FAMILY: "Times New Roman","serif" } LI.MsoNormal { FONT-SIZE: 12pt; MARGIN: 0in 0in 0pt; FONT-FAMILY: "Times New Roman","serif" } DIV.MsoNormal { FONT-SIZE: 12pt; MARGIN: 0in 0in 0pt; FONT-FAMILY: "Times New Roman","serif" } A:link { COLOR: blue; TEXT-DECORATION: underline; mso-style-priority: 99 } SPAN.MsoHyperlink { COLOR: blue; TEXT-DECORATION: underline; mso-style-priority: 99 } A:visited { COLOR: purple; TEXT-DECORATION: underline; mso-style-priority: 99 } SPAN.MsoHyperlinkFollowed { COLOR: purple; TEXT-DECORATION: underline; mso-style-priority: 99 } P { FONT-SIZE: 12pt; MARGIN: 0in 0in 16.2pt; FONT-FAMILY: "Times New Roman","serif"; mso-style-priority: 99 } SPAN.EmailStyle18 { COLOR: #1f497d; FONT-FAMILY: "Calibri","sans-serif"; mso-style-type: personal } SPAN.EmailStyle19 { COLOR: #1f497d; FONT-FAMILY: "Calibri","sans-serif"; mso-style-type: personal } SPAN.EmailStyle20 { COLOR: #1f497d; FONT-FAMILY: "Calibri","sans-serif"; mso-style-type: personal } SPAN.EmailStyle22 { COLOR: #1f497d; FONT-FAMILY: "Calibri","sans-serif"; mso-style-type: personal-reply } .MsoChpDefault { FONT-SIZE: 10pt; mso-style-type: export-only } DIV.Section1 { page: Section1 } You need files in setup. Extract to floppy (all of them) F6 at setup. add a floppy drive.. or create another XP setup disk and place SCSI driver accordinly. You may have to take out the HDD - find the drivers for that HDD at western digical - m5287.sys
ULISATA.INF
ULISATA.CAT(optional)

http://www.techpowerup.com/downloads/408/ULI_SATA_RAID_Floppy_Driver_v6.2.2.1_Beta.html
copied those files in a floppy inside a folder "WIN_XP".. then during setup f6 for driver selection.. then i just located tat floppy for drivers and my drive thus got recognised

Posted on Jan 26, 2009

  • 10406 Answers

SOURCE: boot block compatible ver.024

Bad BIOS checksum: the software on a chip on the motherboard has become corrupted.

Sometimes, you can find a "BIOS update" on the manufacturer's web-site, so that the contents of that chip can be refreshed,
i.e., by booting from a diskette (or from a USB memory-stick) that contains the replacement software.

Contact a qualified technician, and pay them for 1 hour of labour.
Or, replace the motherboard.

Posted on Jul 17, 2009

SOURCE: IDE Ports not working on ASUS P5LD2-VM Mobo

This MOBO requires a driver in order to run the EIDE slot, so before it can be used use the CD-ROM and master HDD in the standard IDE slot to run Windows up then install the drivers then you should be able to rearrange things to have HDD's in the EIDE and other stuff in IDE.

http://uk.asus.com/Motherboards/Intel_Socket_775/P5LD2VM_DH/#download this is the download site, its the 2nd oiption in the RAID category

Posted on May 23, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can I add the 3rd hard drive to XPS 400? Now it only recognises 2 even though there are 3 installed. All are sata and activated in BIOS.


Try going back in the BIOS ( setup menu ) and follow these keystroke commands. Holddown the <Alt> key and depress the <E> then the <F> keys insuccession. This will force the motherboard to load default settings and alsoforce the motherboard to redetect all IDE devices. Note: The selection for thefloppy drive will be set to ON. If you do not have one then you must disablefloppy in set up (BIOS) menu.

Oct 20, 2011 | Dell XPS 400 PC Desktop

1 Answer

The Bios is not recognising the HDD at all nor is windows. I am using a GA-MA78GM-US2H and I have tried it in all Sata Slots on the board 0 throught to 4. I have an IDE plugged into the board as this...


One bad lead can cause a computer to continue on a cycle or to shutdown or fail to detect/ boot up

Test all leads that attach to your hard drive including electrical extensions,IDE,SATA

the leads from your motherboard to your hard drive make sure they have a secure connection and are not faulty or just replace them there probably old and faulty

make sure all leads that are attached to your drives dvd\cd 3 1/2 inch floppy have secure connections and are not faulty or just replace them they are probably old and faulty ?
hope this helps

Dec 18, 2010 | Seagate ST3750640AS-RK 750 GB SATA II Hard...

1 Answer

I recently had a hard drive failure on my HP Pavilion a610n. I decided to replace the IDE drive with an SATA drive. However, the computer will not recognize the SATA drive. I have tried plugging the SATA...


I'm not sure you can insert your OS disk to istall or not, so the solution depends on your being able to do so. It seems to me there's a strong possibility that the BIOS cannot see the drive because that software had basic drivers to recognise the IDE Drive the computer came with.

So, you have to locate the SATA Driver which can be loaded during installation of the OS from either a boot cd or boot floppy. WIndows Setup gives you a chance at the beginning of setup if you watch the progress bar below to press F6 if you need to load a "Third Party or RAID driver" A little further along the setup will stop and prompt you for this driver and you'll need it ready with the exterior CD drive or floppy drive attached with the media in it to load.

It's quite possible this is what you're going to have to do. If this isn't the solution, please don't trash my rating with a thumbs down click. I'm trying to help without complete info.

Best Wishes

Aug 03, 2010 | HP Pavilion A610n (PC106A#ABA) PC Desktop

1 Answer

Can not pick up my hard drive


Check the jumpers on the HDD are not set to slave.

Try a different SATA channel (or IDE channel) on the MOBO.

Try different molex to power the drive up. Hold the drive when it is connected, does it hum indicating that the platter is spinning?

Feb 05, 2010 | Abit VA20 (MBABITVA20) Motherboard

2 Answers

Msi 848p neo v motherboard problems.


Once you reset the bios everything goes to manufactures default settings. You will need to make some changes within the bios. You'll need the help of the manual. See page 3-20.
If your operating system is loaded on to the ATA IDE drive make sure you set bios settings as follows:
Connect the ATA IDE to MB primary master IDE port.
Connect the ATA SATA drive to the MB's first SATA port.

ATA Configuration
Set as, [P-ATA+S-ATA]
S-ATA Keep [Enabled] Set to [Yes] This enables the SATA controller.
P-ATA Keep [Enabled] Set to [Yes] This enables the IDE controller.
On-chip IDE configuration, "ATA Configuration = [P-ATA+S-ATA]".
Next go to Boot menu. Make sure the ATA IDE drive is chosen as boot device three.
First boot device [Floppy] (If you have a floppy disk drive connected.)
Second boot device would be [DVD/CD-ROM] drive. This should be connected to the MB's secondary IDE port & the DVD/CD-ROM drives Master/Slave jumper, set to Master.
Third boot device [ATA IDE drive]
If your boot drive is the SATA drive than set: third boot device to the SATA drive.
(Hard disk drive with operating system loaded on it).
Save your changes & exit the bios.
Keep in mind all ATA SATA drives are seen as Master drives. SATA drives are seen by the SATA controller & in order by their connection to the SATA port number.
Save & exit the bios. The system will auto restart. Windows should start.

Jul 25, 2009 | MSI Computers & Internet

2 Answers

Gigabyte K8vm800M Motherboard Does Not Recognise Seagate SATA HDD


I HAVE THE SAME PROBLEM IN THE PAST. I REPLACE THE IDE HDD WITH SATA AND AFTER I BOOT IT SAYS NO HARDDISK. IT IS BECAUSE WINDOWS XP HAS NO BUILT IN SATA DRIVER.

WHAT YOU SHOULD DO IS CHANGE YOUR HARDDISK TO IDE OR INTEGRATE A SATA DRIVER INTO YOUR XP (USE NLITE) OR USE THE FLOPPY DRIVE TO RUN SATA DRIVER ITS INCLUDED IN THE MOBO WHEN BUYING.

Mar 16, 2009 | Gigabyte GA-K8VM800M Motherboard

1 Answer

Needs help to recover crashed asus r2h bios


You need to put the battery back in, try to find an IDE floppy drive to use and if the new bios version hangs then download the old BIOS and reinstall that -a computer that hangs is not a successful install or the upgrade is wrong. Pulling the battery doesn't revert to the old BIOS, just default settings for the BIOS installed. Using a USB floppy for this is not a good idea as the usb drivers must load -might as well use a thumb drive if this is a laptop. For a desktop stick with the basic IDE floppy drive. Best of luck, Steve Medley

Nov 07, 2008 | Computers & Internet

1 Answer

Strating up problem


Please update MB with the latest bios version:
http://www.ecs.com.tw/ECSWebSite/Products/ProductsDetail.aspx?detailid=685&DetailName=Bios&MenuID=1&LanID=9
Flash from a floppy disk. Re check bios after flash. Go to Boot section. Make sure you have the correct drive listed in the boot order. If trouble still continues. Go to the serial ATA SATA hard drive's manufactures site. Download the tools/utilities & set the drive up with their bootable floppy disk software.
(Do this without the IDE connected to the system). Try installing windows. You shouldn't have a problem. (The bootable floppy can also test the drive).

Luck!
If problem returns, please include detailed results.
Mike

Jun 03, 2008 | EliteGroup ECS GeForce6100SM-M (1.0)...

2 Answers

Motherboard fails to see Hard Drive...please help


Sounds like you lost an ide channel, swap the ide cables around, primary to secondary and secondary to primary. and see if it recognizes the hard drives and not the cdrom.

I lost an IDE channel and had to install a sata hard drive or run the hard drive and cdrom on the same ribbon. If you run HD and CDROM on same ribbon set both to CS (cable select)

Mar 23, 2008 | Dell Dimension 4600 PC Desktop

1 Answer

Stopped working all of a sudden


Hmnmm.... try getting a new IDE ribbon cord, your existing one may be broken.

Sep 28, 2007 | Sony (MPF920-Z/131) Internal Floppy Drive

Not finding what you are looking for?
ASUS P5KPL-VM Motherboard Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top ASUS Computers & Internet Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18392 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

David
David

Level 3 Expert

778 Answers

Are you an ASUS Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...