Resume button is stuck on - Office Equipment & Supplies

did you hold the start/resume button for at least 3 seconds if this works the dishwasher will start ok but if there is a fault it will fail again best you contact your nearest service agent good luck

Hi.

I will suggest you reset your canon printer, Follow this steps to reset your canon printer.

1. Turn off printer.
2. retaining button Resume/Cancel press button POWER - indicator it will catch fire by green color.
3. let go button Resume/Cancel, continuing to retain POWER.
4. press button Resume/Cancel of 2 times, retaining POWER, after which let go all buttons.
5. when indicator will be lit BY GREEN - press button Resume/Cancel of 4 times.
6. turn off printer by button POWER. Power on later to see what happens.

Found this today (and it worked):
canon waste tank reset for canon i70

Below is a procedure that in most cases should resolve a Canon i70 waste tank issue

1) Close the print head cover, and turn off the printer. While pressing the Resume/Cancel button, press the Power button.

(Do not release the buttons. The LED lights in green to indicate that a function is selectable.)

2) While holding the Power button, release the Resume/Cancel button.

(Do not release the Power button.)

3) While holding the Power button, press the Resume/Cancel button 3 times, and then release the Power and Resume/Cancel buttons.

(Each time the Resume/Cancel button is pressed, the LED lights alternately in either orange or green, starting with orange.)

During initialization, the LED blinks in green.

4) When the LED stops blinking and lights in green, press the Resume/Cancel button 4 times (Each time the Resume/Cancel button is pressed, the LED lights alternately in either orange or green, starting with orange.)

After the function (menu) is selected, press the Power button. The LED lights in green, and the selected function is performed. (When the operation completes, the printer returns to the menu selection mode automatically.)

*** 4 times Green Waste ink counter resetting Both the main and borderless print waste ink counters are cleared.

Canon i70 InkJet Photo Printer

error says that either something is jammed in the purge assembly, the unit on the right that cleans the print-head, or the purge assembly is stuck or broken. If you unplug the printer with the carriage in the center you can use a flashlight to inspect the area on the far right where the print-head parks.



try this>
# Start with printer off
# Press and hold resume Button (triangle in the circle) and click "Power" button. Green led should be on
# While holding the Power button, release the Resume Button.
# Without releasing the Power Button, click "Resume" button for two times and release Both Buttons.
# Click "Resume" for four times then soon click "Power" button, to confirm the selected action (reset counter absorber).
# Turn off the printer and turn on again

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response

Thanks, Joe

I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

there might be some paper stuck in the rollers or which is blocking the sensor hence the msg. just give it a good check

I got error 5100 after a paper jam. There was a small piece of torn paper stuck in the gears, and I had to mess around and move the print cartridges back and forth to get seated back on the ink pads to the right of the printer (if you're looking at it from the front).
Reset the printer by powering it off for 10 seconds and try to repeat a test print.

I was able to get mine to work after a few tries. Good luck.



1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not,
press the Power button once more.
8. Your printer should respond as normal..

let me know if this is helpful to you

this may work for you
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not,
press the Power button once more.
8. Your printer should respond as normal..

mine did the same i theres a bit of plastic above the keyboard romove it carfully stick it back with a bit of celotape the plastic that held it had broke that might help

i think you have aproblim with the main card in side the printer

Try the following procedure: 1)Turn off the printer. Press and hold the Resume/Cancel and Power buttons at the same time. 2)Release the Resume/Cancel button. (continue to hold down the power button) 3)While continuing to hold down the power button press the Resume/Cancel button 3 times then release both buttons. 4)The LED should now be green. Press the Resume/Cancel button 4 times. The led should be green. Power it off and back on and you should be good to go! Please update the question & let us know if the information given was useful to you - Good Luck!